Show us your folders.
-
@Sean said:
one thrown in for the hell of it of my current collection that with a bit of luck will change a bit tonite. will post the new arrivals later.It's completely objective, as in beauty being in the eye of the beholder, but of all the knives pictured, the best looking one is probably the least expensive.
That Orange Zytel KaBar Dozier has classic, simple lines that I find really beautuful.
At less than 20 bucks these are hard to beat for EDC.
Very light clipped into your pocket, very sturdy, and very sharp out of the box - 15 degree edge bevel from the factory.
.
-
@jzmtl said:
My first buck knife, and it's my first wood handled folder too! Blade is hollow grind start from almost top, definitely more of a gentleman's folder, not a hard use knife.
Wowsers, jzmtl! That's a beautiful knife - love the blade shape and dymondwood scales. Better looking than the G10 and FRN versions.
IIRC, the Vantage series is made by Buck in the US - amazing that Buck can make them here and sell them at such low prices. Prices on these are competitive with made in Taiwan and made in China knives.
.
-
Thanks! I love that blade shape a lot too, it's more um, traditional, than my other knives. The high hollow grind is extremely thin, near the edge is only 0.017" thick. There are a few minus points, but after I tuned it the action is very smooth.
Yeah I think it's all made in u.s., that's one of the selling point of it.
-
@jzmtl said:
Thanks! I love that blade shape a lot too, it's more um, traditional, than my other knives. The high hollow grind is extremely thin, near the edge is only 0.017" thick. There are a few minus points, but after I tuned it the action is very smooth.Yeah I think it's all made in u.s., that's one of the selling point of it.
After carrying a lot of knives with different grinds over the years, nowdays I actually prefer a high hollow ground blade for an EDC knife.
Not as tough as a flat grind for heavy use, but a hollow grind seems to cut a little better for me in typical EDC applications.
.
-
yeah it's a real beaut thats for sure. where did you get the buck?
-
Just thought I'd take some pics of my recently cleaned, oiled and fitted with a new pocket clip, Sebenza. Has quite a few character marks in the right light.





-
Just thought I'd take some pics of my recently cleaned, oiled and fitted with a new pocket clip, Sebenza. Has quite a few character marks in the right light.
:o You've halved its value :ahhh
Keep it in the box like everyone else ;)It is rare to actually see a used one. ::)
Mine had a few drips of paint on it yesterday as well >:D
-
Local shop had it on clearance, it was cheaper than u.s. price even after tax, it was their last one and I couldn't pass it up.


-
Just thought I'd take some pics of my recently cleaned, oiled and fitted with a new pocket clip, Sebenza. Has quite a few character marks in the right light.
:o You've halved its value :ahhh
Keep it in the box like everyone else ;)It is rare to actually see a used one. ::)
Mine had a few drips of paint on it yesterday as well >:D
Very nice Ben, that pocket clip looks good ;) Neil, you're only jealous
:) -
nice score on the Altlantic!
-
Thanks. My only salt previously was the tasman, which look wicked but pretty useless for everyday situations. Maybe this one will be more useful.
-
I think I might grab a Lansky sharpening system next purchase so I can try and re profile my pacific salt. Cannot sharpen it the way it comes from the factory with the sharpmaker. Hope you make out ok with your Altlantic which I'm sure you will.
Where did you get it? Mind me asking what it set you back?thanks.
-
Got it at Lebaron for $68. I take your pacific is PE since SE comes pretty acute from factory. What I do is to lay a diamond plate from princess auto against sharpmaker rod, hold it with left hand (wearing cut resistant glove) and profile with right hand. It pretty fast as far as manual reprofile goes. For pacific I'd reprofile with 30° slot, add a 40° microbevel, and sharpen with 40° from then on.
-
@Sean said:
I think I might grab a Lansky sharpening system next purchase so I can try and re profile my pacific salt. Cannot sharpen it the way it comes from the factory with the sharpmaker. Hope you make out ok with your Altlantic which I'm sure you will.
Where did you get it? Mind me asking what it set you back?thanks.
Still no luck then?
Very odd. -
apparently on some of the pacific's the blade is profiled a bit differently near the handle than near the tip. So in my case I have one of those knives that half way up sharpens nicely but the other half will have to be re profiled so it will take an edge. the guys on the spydie forums were letting me know about it. even one of them offered to ship it to him and he would do the job for me which was really nice. I can get a lansky here for a pretty good price so I think I just might for special occasions when a blade needs something like this.
-
Yeah a Lansky seems like a good investment. I plan to one day for the same reason.
-
jzmtl,
do you buy chance happen to have a paramilitary?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
Nice score!