Show off your Sak mod's!
-
@Enginears said:
Shout out to FX on youtube https://m.youtube.com/@decoyboat for posting about this mod a while back. I have been carrying the PioneerX - the openers and wanted to make a 91mm version that had a file, scale tools etc.
I ordered some Tachenmesser scales so they may be going on here, not sure yet.I love it!
Nice job all the way around. -
Finally decided to give a mod a go I've wanted to do for some time, an 84mm with 91mm scissors.
I wanted an urban pocket carry for the things I might need that aren't in easy reach wherever I am. I don't need a heavy duty pry tool. Nor do I need a bottle opener or a can opener (I have these in the kitchen where I am likely to be if I need one). I do need a small 2-3mm flat blade, scissors, file. I also really wanted a smaller philips than standard. Didn't want the keyring. Originally the plan was to use the 58mm combo tool but went with the backside philips in the end and filed down the size to closer to a 0/1.
Of course I've never modified a Victorinox before and haven't really got the tools for the job. No bench press drill for example and no dremel either - although I do have a cheap n' cheerful dremel clone - which broke half way through this mod 🤣
Not wanting to let ignorance, lack of knowledge, talent or tools get in the way of getting something done, I obtained an 84mm Sportsman and liberated a set of OK scissors from an old 91mm Climber. Also managed to source some 2.2mm brass rod.
Dismantling went OK. Managed to avoid damaging the brass bushings. Drilling out bushings by hand can be done relatively successfully. I didn't manage to take many photos during as I did it in my spare time and wasn't sure I'd want a photo record of failure!
I found some guides of others who had done something similar (/topic/42774) so thanks to them. I did end up having to sort out some issues that cropped up along the way and may do further adjustments later. I opted to increase the main blade end to fit 2.5mm brass rod (2.2mm on 84mm as std) rather as this was easier in my case, lacking a drill press.
It's not even close to being nicely finished, but it will do, mainly because it's actually going to be used. The last tool mod is to convert the hook into a small precision flat blade screwdriver (~2mm). Will likely get some easy to remove scales at some point to make it easier to replace the scissor spring if necessary. For me best advice I can give anyone wanting to attempt anything similar is plan it out, don't rush and do plenty of offering up as you go (test fit, adjust, re-test etc etc). And it's probably worth getting a drill press and bench grinder plus dremel (don't forget the goggles!) if doing more complicated work. If I did it again I would probably drill the scissors first and then adjust the spring to fit.

I kept the scissor spring as close to the end as possible and cut a small piece away from the spacer, this way if the spring breaks it can be replaced simply by removing the scales without dismantling the whole thing. However the scissors do close with perhaps just a smidge too much snap so might need to adjust that at some point.

Overall I'm happy with it. It disappears in the pocket in a way that even the 91mm Compact doesn't.


Next up is a Yeoman mod. Probably should have started with that 😁🤣
Full list of alterations:
2 layer 84mm with 91mm scissors
Small file adapted to 3mm flat blade (instead of the nail cleaning end)
Removed keyring
Micarta 84mm plus scales (Taschenmesser)
Reduced Philips to fit smaller size screws.
Cutout on liner to allow scissor spring access if neededStill to do:
Mod hook into precision flat driver (cut out in external liner for access ready).
-
Great mods, fellas. From carrying SAKs for a long time now, I always felt like something in the 84/85 mm range offered the optimum balance for ease of carry and maximum utility. Many members feel like there should be a full-sized pair of scissors in that package. Congrats on some nice work gents. (Qubit: Some nice work there. A few tools would make your next efforts much easier, I think. Your first mod looks great.) Best wishes. G

-
Really dig your mod Qubit, especially with the limited tools you got at hand

-
Thanks for the kind words chaps!
-
The first mod I'm willing to show in public!
I've just done a 2-week roadtrip; here's the knife I made to cover my everyday needs and for on-the-go fixes:
-
Started as a Compact
-
Swapped the corkscrew for a Phillips
-
Added the file / metal saw layer from a Ranger, complete with tiny screwdriver on the reverse
-
Custom brass liners (1mm on the outside; 0.8mm on the inner layers)
-
Olive micarta plus scales from Taschenmesser



-
-
That's one sharp looking SAK right there. Well done!

-
lovely Micarta and brass. Toolset looks highly functional too! 
-
Very very nice work there
Sent from my SAK using Tapatalk
-
Thanks folks. I've learned so much from this board; hoping I can give back as I pick up some skills
-
58mm custom Spydernox Mini Champ
Made from scratch brass scales with toothpick and tweezer slots, Spyderco Ladybug blade, serrated Vic blade, wood saw made from ruler.



-
Really liking that 58mm lazar. Curious, why the Ladybug over the Honeybee?
-
@AzteCypher said:
Really liking that 58mm lazar. Curious, why the Ladybug over the Honeybee?He said that he didn't want to use something made in China, which must make everyday life challenging
Sent from my SAK using Tapatalk
-
@kimchi said:
He said that he didn't want to use something made in China, which must make everyday life challengingSent from my SAK using Tapatalk
The Ladybug blade is also just plain better, it's made with vg10, while the Honeybee is made from 3cr13. Japanese blade vs Chinese blade...seems like an easy choice, not very challenging at all.
-
@lazar said:
The Ladybug blade is also just plain better, it's made with vg10, while the Honeybee is made from 3cr13. Japanese blade vs Chinese blade...seems like an easy choice, not very challenging at all.No, that makes sense. In your separate thread you didn't mention the steel though, you just said it was because it was Chinese.
"Most of what I've seen people do, is use a Honeybee blade, but they are made in China and I didn't want a chinese blade."
Sent from my SAK using Tapatalk
-
@kimchi said:
No, that makes sense. In your separate thread you didn't mention the steel though, you just said it was because it was Chinese."Most of what I've seen people do, is use a Honeybee blade, but they are made in China and I didn't want a chinese blade."
Sent from my SAK using Tapatalk
Guess it's both, if I can avoid buying something made in China, I will.
-
My other Spydernox Mini Champ build with an older Spyderco Ladybug blade. 7 layers, regular Vic blade, serrated a Vic blade too, wood saw made from a nail file. Modified the scale to accept shortened tweezer and toothpick.



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
