GOAT Tools Owners Club
-
Have you guys seen that the web shop is up and running now!?
I ordered the titanium scales and the extra hex drivers this morning and just got an shipment confirmation! -
Evenin' awl

I thought I'd give the GOAT a try-out (light use) I needed to remove a string of those cheap solar powered lights that Mrs Surge had suggested that "we" might like

This particular set had died a few weeks ago but I've not really been here (working overseas ::))
The wire cutters failed miserably and just squashed the outer plastic coating and only cut through on the third attempt. However, the scissors cut like a knife through butter

I tried again using my Surge and no issues with the wire cutters

I'm going to try and use this thing as much as I can (no EDC in public as in the UK) but, so far, I'm struggling with the OHO being just that. If I have to use another finger to push the release lever (or anything else) back down then how is it OHO

If you have any tips please let me know



-
I thought I'd give the GOAT a try-out (light use) I needed to remove a string of those cheap solar powered lights that Mrs Surge had suggested that "we" might like

This particular set had died a few weeks ago but I've not really been here (working overseas ::))
The wire cutters failed miserably and just squashed the outer plastic coating and only cut through on the third attempt. However, the scissors cut like a knife through butter

I tried again using my Surge and no issues with the wire cutters

I'm going to try and use this thing as much as I can (no EDC in public as in the UK) but, so far, I'm struggling with the OHO being just that. If I have to use another finger to push the release lever (or anything else) back down then how is it OHO

If you have any tips please let me know

Well it's a real bummer that the wire cutters turned out so bad, I really hope that they are working on a replacement part ASAP.
Regarding no EDC in the UK, I find the Goat the perfect (and first) tool that i actually can EDC because i can remove or replace the blades etc. with other tools (I'm in Sweden, it's strictly forbidden to wear any form of knife or sharp tool outside of your home or work).
-
@Herman Axtelius said:
Well it's a real bummer that the wire cutters turned out so bad, I really hope that they are working on a replacement part ASAP.Regarding no EDC in the UK, I find the Goat the perfect (and first) tool that i actually can EDC because i can remove or replace the blades etc. with other tools (I'm in Sweden, it's strictly forbidden to wear any form of knife or sharp tool outside of your home or work).
As I said, I'll try and use this wherever possible so maybe my views will change

I hope to have my view changed as it wasn't too cheap and took forever to get here :ahhh :ahhh :ahhh
Notwithstanding, the ingenuity to design a new MT and make it so different is to be applauded

-
So, today I had cause to use the Phillips driver to adjust a few cupboard doors. It did very well and the centred bit made it very easy (not much torque needed though)

However, I am looking after a neighbours garden whilst they are away and used the "hammer" to secure a post. That worked fairly well but as I walked away (triumphant, of course :D) the Phillips bit fell out of the holder and, had I not been paying attention, I would have lost it (the magnet is not strong enough)
Still persevering....

-
@SurgeUk said:
So, today I had cause to use the Phillips driver to adjust a few cupboard doors. It did very well and the centred bit made it very easy (not much torque needed though)
However, I am looking after a neighbours garden whilst they are away and used the "hammer" to secure a post. That worked fairly well but as I walked away (triumphant, of course :D) the Phillips bit fell out of the holder and, had I not been paying attention, I would have lost it (the magnet is not strong enough)
Still persevering....
Wow! Just bought a couple of the same hinges. One of the doors on my kitchen cupboard kept opening with just a breeze, going to replace the hinges today. The new ones have the cupboard holes slightly off, will need to reposition them.
The little Dexter ratchet worked like a charm. Hard to take the bits from the box, but putting the magnetic driver over them pulls them out, then you just have to turn them upside down and you're ready to go.



-
So you fine folks have had your GOAT tools for a few months now. How’s the usage been? I’m curious if anyone has tried theirs as a daily user and gotten a few solid months of review out of it?
-
@Grand_Banana said:
So you fine folks have had your GOAT tools for a few months now. How’s the usage been? I’m curious if anyone has tried theirs as a daily user and gotten a few solid months of review out of it?Whilst I was someone who was an original backer (and waited years, like others) I'm not feeling the love

I don't find the OHO really working as well as say my Surge/Wave & Vic' MTs (not chunky enough)
I awlso struggle with the blade changing (a bit too fiddly)
Basically, I don't really carry it and it lives in its box.
I'll stick with my Surge/Wave/ Vic' etc
I appreciate the thinking and design but it doesn't really work for me

In a word; disappointed

-
Thanks, Surge. I’m sure that’s disappointing. I’ve been wondering if I’m missing out if not. Perhaps there will be a V2 addressing some of these concerns.
-
After a bit of neglect for reasons akin to those voiced by many above and inspired by a few Reddit posts and Youtube videos I have finally given in to this latent urge to improve the wire cutters. To increase the clearance between the side of the object undergoing cutting and the pliers, I have taken a small square file to the latter. Some other users seem to have elected the space between the pivot and cutter insert screws, but for reasons of strength I decided it would be best to remove material on the other side of said screws, and not too much or too close to the screw hole as well as leaving a tapered surface of plier metal. This seems to have helped, although I still feel I have to use more force to cut chicken wire than with a Free P4 or Arc. The centre of the pic below shows where. I thought about using a Dremel as seen on Youtube but had doubts about controllability of a high-RPM sanding bit.
In other news,
-
I have finally been able to lay my greedy hands on several sets of Wiha double-ended bits that turn out to fit inside the bit driver very well. These have been unobtainable in Europe for months. I now know why: they're marketed by Wiha USA.
-
I have fashioned a little box to keep spare implements/blades in, by converting a short length of plastic cable holder with snap-on cover.
-
The items under the preceding two points are demanding to be duly stored together with the tool in a compact carry option. A Skinth Mondo sheath is on order.
Pictures will appear here once the latter item arrives. This concludes this update newsletter.

-
-
One more thing I've done is to Dremel a nail nick into the bit driver. This is difficult to get out otherwise...

-
Would any of the @GOAT Tools owners be willing to write a review? I think we need one for the site and would love to put one up there. It's only fitting, we are the source for everything multitool [emoji6]
Sent from my SM-G996U using Tapatalk
-
@SurgeUk @Adam5 @Dutch_Tooler @pa_strunk
Sent from my SM-G996U using Tapatalk
-
@SurgeUk said:
Basically, I don't really carry it and it lives in its box. I'll stick with my Surge/Wave/ Vic' etcI've wanted a GOAT (of course) since I first saw them on the horizon, but the reports from you and others have dissuaded me.
The whole idea of the GOAT sounds great, but maybe they aren't ready for prime time.

-
These look good. Where are they manufactured?
-
I saw them early on and I was intrigued by the concept but I don't think I'll make the leap at this time.@powernoodle said:
I've wanted a GOAT (of course) since I first saw them on the horizon, but the reports from you and others have dissuaded me.The whole idea of the GOAT sounds great, but maybe they aren't ready for prime time.

-
@David Bowen said:
@SurgeUk @Adam5 @Dutch_Tooler @pa_strunkSent from my SM-G996U using Tapatalk
I'll give it some thought

The trouble is I can't carry it as EDC (UK Laws) and I can't carry it for work (issued kit only) and this severely restricts my usage and, therefore my opinon

It's not a bad MT just doesn't quite cut it for me (no pun intended)

-
Gotcha, if you decide let me know
Sent from my SM-G996U using Tapatalk
-
I might give it a try, but it'll be a while before I can put reasonable time in a review. The short version is: the exchange system is an interesting concept with potential, but execution is a bit wanting as the release lever has started to be so loose as to move when implements are deployed; maybe the release lever handles need securing somehow. The wire cutter layout on the pliers has room for improvement, and so has the file.
-
While we're waiting for a full review, here is a pic of the GOAT Tool
in<u>waiting for</u> action.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login