Leatherman Bond Owners Club
-
The blade was a tiny bit loose and the tip of it would come out of the handle fairly easily :ahhh it just wasn't exactly safe

-
So…
They really did not fix the issue, just changed out the blade with a drop🙄A Wharncliff, sheep foot or a Lamp foot blade would have been even better. 🙂
-
@LoopCutter said:
So…
They really did not fix the issue, just changed out the blade with a drop🙄A Wharncliff, sheep foot or a Lamp foot blade would have been even better. 🙂
The blade on my later version is held into its handle by noticeable tension which
stops it accidentally deploying. -
@Magic Bus said:
The blade on my later version is held into its handle by noticeable tension which
stops it accidentally deploying.Good to hear that

-
@Magic Bus said:



It looks like there has been a change to the knife blade shape, I also note that the knife blade is held into its handle by noticeable tension with the slip joint tab (arrowed). I quite like it and I’m sure it will grow on me
So no more floppy blade.
Anyone wanna buy a lightly used Bond?
-
@HarleyXJGuy said:
So no more floppy blade.Anyone wanna buy a lightly used Bond?
Correct!
Sent from my iPhone using Tapatalk
-
@HarleyXJGuy said:
So no more floppy blade.Anyone wanna buy a lightly used Bond?
Depends on how much
:DYou might be able to contact LM about the blade and send it in for a blade swap though

-
@Poncho65 said:
Depends on how much
:DYou might be able to contact LM about the blade and send it in for a blade swap though

Sure.
Dug out an extra pocket clip and been carrying my Bond the last few days. The floppy blade isn’t really an issue on the Bond so much because it is housed inside the handles.
Added bonus of the clip is making it super easy to locate the blade without looking.
Really wish they would add holes for a clip to the Rebar/ST 300.
Early morning sand pickup.

-
Great pic of the Bond, Harley 8)

I wished that Rebars and ST300s had a spot for a clip as well :ahhh
-
I am one that is happy did not predrill and tap screws holes for the REBAR AND ST300.
Both tools are too heavy for a pocket clip. I had no issues carrying in the sheath on the belt behind the belt loop before the right back pocket. And, now one rides in my shoulder bag for events and hike excursions I get involved with.
The tapped holes on the BOND drove me nuts until I installed the clip. Should have been included in the package.
The pocket solution I have adopted for the REBAR and will work for the ST300, Surge, and WAVE / Charge models is utilize the lanyard loop, cut a piece of paracord about 14 to 20”, attach a lobster claw or clip to the cord. Tie it in sloop. Then thread it onto your belt, attach the clip to the tool and slide into pocket.
When needed, just pull the cord to retrieve the tool, un-Clip and use.For the tool to stay vertical just shorten the cord to keep the tool from laying in bottom of pocket.
Much less expensive than any clip. I have a cord made for the purpose, will retrieve and picture. 😉
-
@LoopCutter said:
I am one that is happy did not predrill and tap screws holes for the REBAR AND ST300.Both tools are too heavy for a pocket clip. I had no issues carrying in the sheath on the belt behind the belt loop before the right back pocket. And, now one rides in my shoulder bag for events and hike excursions I get involved with.
The tapped holes on the BOND drove me nuts until I installed the clip. Should have been included in the package.
The pocket solution I have adopted for the REBAR and will work for the ST300, Surge, and WAVE / Charge models is utilize the lanyard loop, cut a piece of paracord about 14 to 20”, attach a lobster claw or clip to the cord. Tie it in sloop. Then thread it onto your belt, attach the clip to the tool and slide into pocket.
When needed, just pull the cord to retrieve the tool, un-Clip and use.For the tool to stay vertical just shorten the cord to keep the tool from laying in bottom of pocket.
Much less expensive than any clip. I have a cord made for the purpose, will retrieve and picture. 😉
Is the Rebar that much heavier then a Bond?
As you know I am also a big fan of sheaths but sometimes mixing it up is nice.
-
@HarleyXJGuy said:
A couple of what?Must have autocorrected to that, it was suppose to have been clip
:D

-
@LoopCutter said:
I am one that is happy did not predrill and tap screws holes for the REBAR AND ST300.Both tools are too heavy for a pocket clip. I had no issues carrying in the sheath on the belt behind the belt loop before the right back pocket. And, now one rides in my shoulder bag for events and hike excursions I get involved with.
The tapped holes on the BOND drove me nuts until I installed the clip. Should have been included in the package.
The pocket solution I have adopted for the REBAR and will work for the ST300, Surge, and WAVE / Charge models is utilize the lanyard loop, cut a piece of paracord about 14 to 20”, attach a lobster claw or clip to the cord. Tie it in sloop. Then thread it onto your belt, attach the clip to the tool and slide into pocket.
When needed, just pull the cord to retrieve the tool, un-Clip and use.For the tool to stay vertical just shorten the cord to keep the tool from laying in bottom of pocket.
Much less expensive than any clip. I have a cord made for the purpose, will retrieve and picture. 😉
I have a clip on a Rebar and really love it
they do weigh less than a Wave or Charge, I believe
I have pocket carried a Surge, so I know a ST300 is definitely possible as well 
Even if it wasn't the holes for the Free type clip, they should have an option for one

-
@HarleyXJGuy said:
A couple of what?Tapped screw holes is what read he meant!😁
-
I should also include that I sheath carry 5 days a week for work and love that method as well
I just prefer not to sheath carry when I am just out on weekends (unless I am doing lots of yard work of course ;) ) or just making a trip to town or eating out :D and that is my reasoning for wanting a clip option for everything
I have pocket carried ST300, Surge, Rebar, PSTs and the like plenty and a clip would have been definitely nice 
-
As promised, the lanyard solution I have used with pocket carry of Fixed blade Izula in Sheath.
Can be employed with Rebar or ST300.
This lead is longer as it intends for the base of the sheath to be at bottom of pocket. I would shorten 6 - 8” d pending on how deep your pockets are.
[attach id=0 msg=2469516]
[attach id=1 msg=2469516]Sorry for poor pictures😌
And s as los the weights of the REBAr and the BOND
[attach id=2 msg=2469516] 189 g Rebar
[attach id=3 msg=2469516] 168 g Bond



-
Hmm pretty close in weight.
Come on LM get it done.
-
Since installing the pocket clip the Bond hasn’t left my side.
Got a new batch of magazines in so the Bond was pressed into service to help install the correct base plates.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login