Tinker Tuesday!
-
The in between Super Stinker. I mean Tuper Tinker. Here it is anyway. Best wishes. G
:D
[attach id=0 msg=2474062].jpg)
-
You know, the Deluxe Tinker was the first Victorinox I'd bought in a while. But it's weird -- the tools don't really snap back into place like my other Vics, and the scales are not completely flush with the body. I don't know if that's just this specific one or what, but it just feels very different from my older ones.
-
How about a photo, Tuisto? One picture is worth a thousand verbs, right? Two pictures would be better, now that I Tink about it.
If it is a used knife, then it needs a good clean up and a little lube to restore the snap. Scales can be pressed back on their pins if they are not fitting flush.
Best wishes. G
:ahhh -
Fair enough, here are the photos. It's absolutely brand new, I bought it less than a month ago (from an extremely large online retailer that shares the name of an ancient Scythian all-female warrior tribe). Not quite sure if I can show with pictures the issue with the snapping, but certainly you can see the red part of the scale extending over top of the metal part, which occurs in absolutely none of my old(er) SAKs. And this is actually after I replaced this one already via that enormous online retailer -- this is the second one I received that still doesn't snap and still has issues with the scale (albeit, not as bad in the case of the latter). I'm sorry, I'm editing this to add that it's the cap lifter layer specifically that doesn't snap.



-
I would definitely drop a little bit of mineral oil in that joint and work it back and forth. Though it being brand new, you shouldn't have that type of issue. I would give that a go when you get a minute.
As far as the scales, not sure on that. Might just be that a batch of the celidor scales were fitted improperly or cut slightly differently?
-
@AzteCypher said:
I would definitely drop a little bit of mineral oil in that joint and work it back and forth. Though it being brand new, you shouldn't have that type of issue. I would give that a go when you get a minute.As far as the scales, not sure on that. Might just be that a batch of the celidor scales were fitted improperly or cut slightly differently?
Thank you for that advice. I have a lot of SAKs; I'm a big fan of Victorinox. I have always tried lubing it but never working it back and forth after -- that seemed to do the trick! It's weird, I've purchased a few Vics recently and seemingly the scales are all... a bit off. I don't know if they're just making them differently now or what but they seem a bit weird. I actually got a sapphire Swiss Champ from them with a bent corkscrew right out of the box. I didn't even notice it at first and now I think it may be too late to try to replace it.
-
Sorry to hear this. Give it shot so they know what's going on! Good luck.
-
Time to Tinker around. Again. I took the Tinker on yard maintenance yesterday. An alder broke down in the yard, so I cut some of the worst parts off. Might post a photo if I decide it isn't too boring. Whackulated some invasive privet and some invasive multi-flora rose. Made zizzing noises with my old Echo. Picked up some deadfalls. Normal stuff.
Best wishes. G
:) [attach id=0 msg=2474802]
-
Here's my Tinker Deluxe which was given a new lease on life thanks to AzteCypher's instructions (below)! I really do love this model. I love Vic scissors and pliers and this is the smallest model that I'm aware of that has both. I want to replace the scales with blue Plus scales because I love the little pen. (But to be completely honest, I really wish this thing had the corkscrew instead of the Phillips because I use the glasses screwdriver a lot more than the backside Phillips (or the corkscrew, for that matter). And the version of this thing with a corkscrew instead of a Phillips is the Deluxe Climber (shown alongside the TD for comparison). But then again, I use the pin more than the glasses screwdriver and the Deluxe Clmber doesn't have the pin hole. Anyone got any tips?
@AzteCypher said:
I would definitely drop a little bit of mineral oil in that joint and work it back and forth. Though it being brand new, you shouldn't have that type of issue. I would give that a go when you get a minute.



-
Nice. I think you could figure out how to make a pinhole in the scale. Looks like the corkscrew side scale is damaged now. That would be a good one to experiment with. There have been some posts here about converting the scale for a pin. Might want to look them up. Best wishes. G
:D -
@IMR4198 said:
Nice. I think you could figure out how to make a pinhole in the scale. Looks like the corkscrew side scale is damaged now. That would be a good one to experiment with. There have been some posts here about converting the scale for a pin. Might want to look them up. Best wishes. G
:DYou know what, that's a great point actually. Since the scale is already damaged, and I would prefer plus scales anyways, I should just swap the entire scale for plus scales and get the pin hole as a bonus. Does anyone know when they started making the pin holes in all the scales?
-
The chart says 2009 but adds a question mark. Best wishes. G

-
Not sure which part of the world you're from but I found these on eBay.
-
@AzteCypher said:
Not sure which part of the world you're from but I found these on eBay.I'm not originally from here but I'm living in Athens, GA for the time being.
-
Black Tinker for today. Best wishes. G
:D [attach id=0 msg=2475761]
-
I picked up this unique Tinker recently. There is no Victorinox emblem on the front scale only the Witraktor wording. No scale tools, a small clip point blade instead of the small spear point, and a square Phillips with the file.

-
Nice. That one has been around a while. I see the Pat markings on the can opener. Are you carrying a SAK now? Best wishes. G

-
Yup, I'm only doing the Fire challenge so I've been carrying a SAK for a bit. I've been itching to find a square Phillips with a file and I finally got one. Strange that there's no shield on it though. Custom request for a company I'd wager.
-
Great choice! I must admit I have a bit of a soft spot for black Tinkers
@AzteCypher said:
There is no Victorinox emblem on the front scale...Another great one! Is the Swiss cross on the back scale?
I may well take a Tinker photo when I get home.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
