Sharpening methods
-
You all have this modern new stuff! This somewhat reliable water stone have sharpened lots of knives over the years. It actually started out with a far bigger diameter... Still works! Two man operation works as social media too!


-
Over the years I have bought a lot of different sharping tools. Most of them are not very good at taking a rounded dull blade back to razor sharp. I buy old rusty tools and knives a lot of them have broken tips, hatches, hammers, and other tools. I found it very easy to regrind an edge on a knife using a Harbor Fright one-inch belt sander with a 600 belt. Practice with an old table knife. Next, I use the fine side of a Worksharp Field sharpener with some WD-40 on the plate. It only takes two or three alternating passes. Then do a few passes with a white ceramic rod and finish up by stropping on a cheap mouse pad almost flat with very little pressure without compound. Swiss Army knives, cheap knives, sharpen up nice But the old carbon steel knives turn out crazy sharp. The stone I carry with me is an Opinel four-inch stone.
-
I’ve been using a DMT Aligner set for a long while. It seems to work pretty good for most my knives. I’ve tried a couple other systems, but seeing that most my knives are pocket knives it seems to work well. I have replaced a couple of the stones.
-
@algernonramone said:
This one's my favorite, I use it for all my sharpening right now. Like to get a bigger/better system someday, but for now this does the job, and does it well.Nothing wrong with the Field Sharpener. I have one, and it's one of WS"s best selling items for a reason. Mine doesn't get used no where as much as it should. It takes the simplicity of freehand, and gives a little assistance for those new to sharpening.
Sent from my SM-G996U using Tapatalk
-
@Doc said:
I have the Work Sharp Precision Adjust Elite, and Field Sharpener, some Lansky Pucks (love ‘em), and a Norton oil stone (love it). My sharpening skills are definitely not a strong point, but I muddle my way through most of my collection okay because I am definitely not a knife steel snob. The vast majority of my knives are 1095, so I don’t need to be particularly proficient. I do want to add this, hoping I don’t get kicked of this thread for posting abomination, but after decades of muddling my way through better or worse sharpening attempts, I have discovered the absolute joy of relying VERY heavily on utility blades. I always have a knife and an MT on me, and it varies day to day as to which. However, over the past year or so I have become a utility blade kool-aid drinker. I use them for at least 80% of my cutting tasks, and they cut much better than any blade I can sharpen. I think my favorite aspect is when I notice a decline in slicing ability, just spinning the blade around or changing it out in less than a minute, including the walk to the box of blades. Cool? Nope. Lazy? Maybe. I have my BK 2, 7, 14, 18, et al, for extraordinary (for me) tasks, but given day to day cutting chores, I don’t need to sharpen any more, which I think is a very good thing.Nothing wrong with utility blades, many people use them in place of knives that need sharpening. Sharpening is a skill that some people have yet to master, and utility blade knives are popular for that reason. Plus there's a host of blades with titanium all the way to DeWalt carbide. They can often have as good an edge retention as a good modern steel.
Sent from my SM-G996U using Tapatalk
-
I don't have any of the Ken Onion branded WS products yet, maybe in the future. I definitely want to check them out, my work uses one for guys in the meat dept who don't sharpen worth a toot
Sent from my SM-G996U using Tapatalk
-
@Sos24 said:
I’ve been using a DMT Aligner set for a long while. It seems to work pretty good for most my knives. I’ve tried a couple other systems, but seeing that most my knives are pocket knives it seems to work well. I have replaced a couple of the stones.I've yet to check out a DMT Aligner, maybe this fall I'll get the chance. It's similar in function to the Lansky/Gatco I feel. DMT makes good products, I hear people complain about quality from time to time but nothing crazy.
Sent from my SM-G996U using Tapatalk
-
@David Bowen said:
Nothing wrong with the Field Sharpener. I have one, and it's one of WS"s best selling items for a reason. Mine doesn't get used no where as much as it should. It takes the simplicity of freehand, and gives a little assistance for those new to sharpening.Sent from my SM-G996U using Tapatalk
I have been using the field sharpener for my traditional knives. What works best for me is rather than grip the end, I lay it flat on the palm of my hand.
That way it does not wobble and it stops me from using too much pressure.. -
This video has put me off the mk2 for now.
https://youtu.be/1R0zWkb2k6s?si=rItYEUnQPu3S2KJp -
that looks handy
-
I have the mk1 and it took some practice. Because if you are using a coarse grit or have the belt running too fast it’s easy to remove to much metal.
So until you perfect your consistency of pass keep it finer and belt speed slower. Then once you get your confidence you increase the speed to your sweet spot.And start on knives that it does not matter if you dou ruin them. I am quite proficient but still would worry about sharpening an expensivie knife for now because I’m not “muscle memory” good yet.
-
@chip said:
I have the mk1 and it took some practice. Because if you are using a coarse grit or have the belt running too fast it’s easy to remove to much metal.
So until you perfect your consistency of pass keep it finer and belt speed slower. Then once you get your confidence you increase the speed to your sweet spot.And start on knives that it does not matter if you you ruin them. I am quite proficient but still would worry about sharpening an expensive knife for now because I’m not “muscle memory” good yet.
-
I picked up a used Mk1 but I still need to learn how to use it. Give it a bit of a go on my lawnmower blade and I did ok. Definitely need more practice before I start using it on my nice knives.
-
@AzteCypher said:
I picked up a used Mk1 but I still need to learn how to use it. Give it a bit of a go on my lawnmower blade and I did ok. Definitely need more practice before I start using it on my nice knives.That's what kitchen knives and Opinels are for.

-
@pfrsantos said:
That's what kitchen knives and Opinels are for.

And even better if you can learn on other peoples kitchen knives like I did

-
I actually do have a few I can practice on. Need to make time this weekend.
-
@AzteCypher said:
I actually do have a few I can practice on. Need to make time this weekend.
practice makes perfect. -
Also when using the worksharp elite it creates a good burr due to the fact you are sharpening edge trailing. Which is really helpful because you can literally watch it form once you hit the edge as you make a pass.
I am getting better at stropping but no way as good as I would like to be, so found making a few passes on a very fine ceramic rod was excellent at knocking off the burrs.
-
Try using a light oil on your diamond stones it cleans and keeps them from getting plugged up. They work a lot better with oil. I use WD-40 because I buy it buy it by the gallon. I use cutting board oil on knives with wood scales it is a thin mineral oil it looks like it would work well. The three biggest mistakes people make stopping is the wrong angle it is better to start with less angle all flat. As you are finishing a pass on a strop or stone do not let the tip of the blade leave the stone or the strop. when stropping use very light pressure. A rubber mouse pad is much more forgiving than a leather strop.
-
I use glass cleaner (nilglass) as a lapping fluid when using my diamond plates to stop them from clogging.
And then a quick spray and wipe down when I am done keeps them clean.
Also any glass cleaner residue left behind evaporates much quicker than water. Never had any problems with rust.I too use chopping board oil on all my knives as it’s very cheap and food safe.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login