Knipex Owners Club
-
*
Deciding which one to pocket carry can be difficult. The Pliers Wrench is grippier on fasteners and doesn't chew them up, but the Cobra is a better all-around grabber. Dang it! -
That's a tricky one! :D
-
It’s so sweeet

-
And useful,
It gets to work a lot when I am splicing ropes to extract the needle while stitching
-
@nakken said:
Nice one Tasky, I am having a hard time deciding whether to get a 125mm or 100mm. Keep us posted
Well..... they suck, if I'm brutally honest.
So often I've found the need for pliers over the past 8 months and these have fit the role very nicely, but with the one INFURIATING factor of being one-way!!!
The amount of times I've juuuuuuuust managed to fit the jaws to task, only to find they simply slip on the work and I have no room to fit them on the other way has had me livid. I know they're meant specifically for plumbing and have the smooth edge to facilitate a sort of ratcheting action, but that just halves the number of situations in which they can be used.I'll still carry them, but only until I find something better that lets me push and pull however I require.
-
Tiny spaces are the worst indeed. Sometimes I wonder what people were thinking when then designed certain stuff. Hydraulic manifolds have driven me beyond crazy more than once. One was made so tight that only the end ones could be removed. Thus to remove one in the center you had to remove all the ones above just to get tooling attached. Evil madness! (And that was even specially bought narrow tooling).
Then there was this old car where I tried to change some component deep down in the engine. The bolts were stuck on the engine side, and the component had holes. However after removing the nuts I realized that the component didn't have space to slide off the bolts. The entire engine would have to be taken out to make enough space...

But I've found lots of uses for the plier wrenches, so while not suited for all things they are great at what they do - if you need that :)
-
I've accumulated a few over the last 10 years!
I don't EDC any of them though...A few more are tucked into drawers and other toolkits...

The stubby needle nose combo pliers 0822145 are by far my most used general purpose pliers. They are pretty much the same size as the pliers on a LM Surge.
[attach id=0 msg=2478388]
The 6 inch pliers wrench is also a go-to around the house.

-
Yes, it is weird how often that one seems just right. Goldilocks factor for many small tasks.
-
@Brock O Lee said:
I've accumulated a few over the last 10 years!
I don't EDC any of them though...A few more are tucked into drawers and other toolkits...

The stubby needle nose combo pliers 0822145 are by far my most used general purpose pliers. They are pretty much the same size as the pliers on a LM Surge.
The 6 inch pliers wrench is also a go-to around the house.
The stubby needle nose combo pliers is my favourite too. So much so that I bought an extra one to put in my Chainsaw tool roll (it's good for installing those pesky e-clips). Unfortunately the pivot was slightly stiff, even after lubing and much opening and closing. It's not too bad, but it's the first Knipex that wasn't perfect straight out of the box (and I have a couple of dozen others).
-
Proudly using Knipex since 2008 having alot of their products. I am mostly proud of modifying the plier wrenches several years ago into adjustable spanner wrenches for cycling mechanics and F-35 maintainers.


-
I like that.

I sometimes have two use two at once and where one has to hold a narrow nut without getting in the way of the other. That should do the trick!
-
Knipex is releasing a 150mm and 250mm Twin-Grip! :ahhh
I think the OG 200mm is big enough, but I'll get the 150mm to add to my 150mm Plierwrench and Cobra and 160mm CoBolt.
Hold still, myheartwallet.
-
That's good to hear. The current Twin Grip is a nice set of pliers, and pretty reasonably priced (for a Knipex).
-
Gonna take a 150 for sure, I waited since the release of the original one for that size
-
@ReamerPunch said:
Knipex is releasing a 150mm and 250mm Twin-Grip! :ahhhAh, they are merciless! :ahhh
That said I already have a smaller Engineer Neji-Saurus plier (which was likely an inspiration anyway), so my sensible judgement might get the better of me this time around.
-
*
Twin Grip in 150 and 200mm. The smaller version would be good in a belt pouch or small tool kit. The 200mm is more of a general use plier that hits the sweet spot for me.*
-

The Twin Grip 250 is a Big Momma. -
TwinGrip 150mm is in!


-
@ReamerPunch said:
TwinGrip 150mm is in!
I've got that one too. Its small enough to almost be pocketable.
-
I think I paid something like that for my 200mm TwinGrip with comfort grip handles. Absolutely crazy cheap for what it is. Cheaper than the 100mm pliers wrench, maybe even the 100mm Cobra. :ahhh
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
