What did you use your Sak on today?
-
Used the flathead screwdriver on my Fieldmaster to help take a part a knockoff pocket knife I had since I was kid. I want to mod a Compact I have, so this was some practice. Also my first message on the forum so Hi Alll!
-
Did use the flathead screwdriver part of the Huntsman Bottle Opener to clean up these discussing toothpaste remainings from my Electric Tootbrush Charging Station..
-
Servicing lawn mower:

Sent from my iPhone using Tapatalk
-
I used the small blade on my Tinker to cut a label off a plastic bottle before putting it in the recycle container. Also used the Tinker awl to open a container of floss.
-
I did try the Rimer Blade (Aale) on my new Alox Pioneer X on a bit Packing Foil when I emptied a Honey Jar Palette this morning..
yes this tool works quite nice for cutting stuff you want use your Main Blade ^^ -
I ordered 9 door and window sensors for my Home Assistant integration which arrived, today. I used the nail-file on my Midnite Manager to open them and insert the cr2032 batteries, then used the pen on the same knife to label the boxes with their intended installation location. I could use the flashlight to install them in the dark, but I'll just do it in the daylight... but maybe not!
[attach id=0 msg=2490696]
-
Cybertool S in the garden, today. Used the pin to unclog one of my sprinkler emitters. Very satisfying!
[attach id=0 msg=2490918]
-
Did cut some bagels whit the main blade of my new Alox Pioneer X; it’s actually quite sharp , but was to expect..

-
My SilverTech scaled Champion Plus helped to clear jamming residue from Walker’s cylinder:

Sent from my iPhone using Tapatalk
-
Spider-Man was in distress! His leg was broken, and the Swiss Champ pliers were perfect for holding the tiny leg in place while the superglue worked its magic.

-
Did some pruning on the kitchen plants while drinking my morning coffee.
Midnite Manager. [attach id=0 msg=2492420]
-
Whe have some Lip Balm Sticks in our Beekeeper Shop for Sale, but as i have to try them myself out to tell the Customers how good they are i had the whole time one from one Brand which was actually quite good and did also hold up quite well, maybe i did use it for too long as you would quess during Corona you dont want to wear Lip Balm as its would make the Mask a bit sticky.. after this was empty whe became new ones ..
unfortunally i did trop one during unpacking so i did decide to use this as my own Tester ..
Its much softer and maybe not that heat resisting so its dosnt hold up that good as the other, the Balm Itsellf is good though ..So yesterday i wantet to use it but it brook from the pusher and did stick in the Tube, so i used this "Spatel" Tool of my Minichamp to wiggle it a bit loose, and now its back in working condition ..
-
Did use these meassure engraving on my in the 90tes in Bayovarian bought Swisstool (its the old Blocky one) to meassure which of my Knives where under 6 cm Blade as this is the Magical Lenght the German Gouvermend wants to keep allowed ..
Was a bit Scared that i dont have that much under 6 cm: The 58 mm SAKS, (Minichamp and Classic SD) and surprise: An Leatherman ^^ The Juice XE6 ..And the a few mm too long Blade of my Alox Pioneer for Cutting a Bun , do this some times..
-
The corkscrew came in handy when the cork stopper broke off in the bottle

-
I used my Victorinox Mini-Tools as Watch Bracelet Link Pin Pusher, also i used it as SIM Card Eject Pin Tool
[attach id=0 msg=2495916]
-
The Philips head screwdriver on my Skipper was used to help swap out some bulbs in living room light fixtures. Can opener on my Tinker was used to open a soup can for lunch yesterday. Next, the package opener on Spirit was used to open the packaging of new house numbers last night. Lastly, Spirit pliers were used all weekend to pull nails and assorted fasteners from walls before house spackling and painting took place.
-
You've been busy! I can only hope all the projects go well.
-
Did some drilling, filing, chiseling, and awlso prying to install a deadbolt mechanism and fix the hinges. Always fun to use a hole saw and spade bits.
An alox cap lifter and small rubber mallet are just perfect for tapping out door hinge pins. Had to realign one of them with Spirit pliers and filed out the inside. It was scratching the pin and grinding? Somebody did a number to it in the last 50 years it’s been up there.
The chisel is just perfect to set the initial strike mortise and then bored out to depth my dremel. Set the initial screw placement with the Spirit awl and Phillips.
[attach id=0 msg=2496476]

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

