What did you use your Leatherman for today?
-
I am making a new rectifier mounting plate for my motorcycle and even though I have prob 15 various pairs of pliers in my tool box I used my P4 to pull off the aluminum melt around the edges where I ground it. Solid grip! Also used the file on a small edge that I didn’t feel like getting my dremel out for. Worked great; def earning its spot already
-
Got wheel back. Had two broken spokes, and removed one good spoke for measurement. Ordered spokes. Found a shop to replace and true the wheel. Was down 2 weeks. As I was installing the NuVinci n380 had noticed the drive cog was loose. Removed the workings, found the clip came off, used Garage 5's fixed flathead to get the ring back on, then snugged it in around the outer edges.
Then found out I had to reset the rotating controller. Took longer to look up the instructions than it was to get that aligned, and did the OverDrive option. G#5 was there to help get the wheel back in and the chain up and over the cog.
Did employ the use of a very old cycling tool since it was handy, and I misplaced a crescent wrench.



-
[attach id=0 msg=2492347]
Ol' reliable helping out in the garden. Finally remembered to snap a picture

-
Looks like that Juice has seen some use! What model is it?
-
It's a pro. I've only had it for like 2 years. It's definitely seen some use before me tho.
-
The only Juice I presently own is a Pro. I like it a lot, but being long out of production, it doesn't see much carry time.
-
Great pic 8)
Kudos for using a Juice Pro as well

-
@Farmer X said:
The only Juice I presently own is a Pro. I like it a lot, but being long out of production, it doesn't see much carry time.This one was missing a spring on the small flathead side when I got it. I found a beat up cs4 and broke it down so now I have extra springs and tools if the pro breaks.
-
Made this a while ago but I still want to share :D My mini DIY project - a portable guitar amp
Not having much experiment with soldering stuff so I struggled and learned a bit after this project. Plus this is my first 3D print as well. Used the Wave+ to help cut and strip some wires, and the file to do some rough work on the case before finishing with finer sandpaper
If anyone interested in the schematic of this amp, it's called Ruby model by runoffgroove.com
-
A colleague of mine lost a screw at a hinge between a len and a temple of his glasses. Handed him the Wave+ pliers so that he can put a straightened metal paperclip through the screw hole and bend the ends a bit to make the clip stayed in place. Used the cutters to cut the excess. Not a permanent solution but it should be fine until he can get another replacement screw. :D
-
Cutting pvc sheets to cover books for my daughter for her new school year with the surge scissors, using the gap between tiles on floor as guide.

-
Very nice.

Best wishes. Gary -
Used the plier of bond to disconnect two connectors of my Hypervolt massage gun.
The screws are PH1 and a bit deep, didn't use the one in LM.
The thing heats up quite a bit at where the piston motion is (where a part rubs against a tube of the body). Disassembled to get to know where to lubricate. Will service it when I get hold of some lithium grease.

-
Nothing of crazy uses but I used the Wave+ can opener to open a can of condensed milk today :D
-
I have a can of sweetened condensed milk laying around, and I think I'll enjoy it tomorrow. -
I also used a Leatherman can opener today, but it was the one in my Surge. I know, I know.

Happy to report that it functioned flawlessly. -
I needed two of them to open an Imodium pack. Not sure how people are supposed to do those without pliers or scissors, actually.
-
That's so true...some of that pill packaging is way too hard to open!
-
Having tiny cactus thorns stuck to my finger.s I don't have tweezers around and it's too small to grab with pliers. However I was able to grab the tiny thorns between the Wave+ blade and my opposite hand's thumb nail.

-
I fought with some heat-sealed packaging using the awl and serrated blade on the Surge today. I sincerely hope there’s a special place in hell for whoever designed that stuff where they just have to try to open it with their bare hands for eternity.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login