What Did You Use Your Multitool For Today?
-
My Huntsman is getting a lot of carry time at the moment. Opening boxes and cutting card at work today.
-
one of my foundations failed inspection today b/c some of the rebar was'nt tied off correctly to the chairs (support for the steel so that it does not sit flat on the footing). all i had was a few chairs laying around to use as tie wire so i decided to see if the LM kick could take it. these wire chairs are heavey gage steel and i was skeptical but the kick had no problem cutting the chairs up and tying off the rebar was a breeze.

-
Slow day for my tools today... Today I used a screwdriver bit extension and my CRKT Zilla tool (which I won here at MT.O) ;) to repair the broken handle on my vacuum cleaner (it was cracked and dislodged from the rest of the vacuum). I had to disassemble the vacuum cleaner handle and then reassemble it so it fit properly again.
-
Used the file on the SuperTool to remove burs from a small shaft when i was rebuilding the HVA on a homogenizer at work
-
My mother has just had some loft insulation fitted so a bunch of old stuff had to come out. Amongst it was a pile of paperwork and photos belonging to my great grandmother. So today's most used tool was the magnifier on my Scientist pouring over the photographs trying to figure who everyone was. Its a real treasure trove to add to our family archive. My wife's big into genealogy so she got very excited :)
-
Sounds interesting

On a much less fascinating note, I used a PST to change a loo seat :P
-
whew... busy day.
used the spirit to cut off several RG6 wires to roll them up nicely for the new homeowner. this was the only task the vic came up short. it took rotating the wire and making another cut.
used the pliers to poke out the dried mud in a water meter lid and then picked it up with the pliers to place it on the meter. (note to self, get another landscaper)
used the wire cutters to shorten up the low voltage wires for the garage door operator of that home.
used the pliers to pull a nail out of my rear tire so i could plug it (note to self: need to buy more rubber cement)
used the flat head or the can opener to screw on an outlet cover for a microwave.
used the phillips to tighten up a base door stop.
used the PE blade to cut out some glue left on the carpet (still can't figure out how that got there)
used the phillips again to remove the base mount of a towel ring in the master bath of the 1st home. got ticked off b/c i could'nt remount it b/c of the POS mounting screws the installer used.
finally, used the pliers again to repair a sprinkler head that popped off of its base on this home.
i washed out the grit from the water meter lid in the kitchen sink when i got home. steeled the PE blade... good as new. :sak: -
Used the screwdriver/caplifter on my SwissChamp to (very gently) open up stiff blades on a '31 Vic and a '51 Wenger Soldier for cleaning and oiling.

:D :D :D
:tool:
-
Used my Charge Ti and mini screwdriver to fix my niece's laptop today. The battery exploded and totally ruined ("melted" is a better word) the contact plate so I unscrewed the laptop housing with my mini screwdriver and used the Charge's wire cutters to cut and re-strip the wires that were soldered to the contact plate. I then installed a new contact plate and re-soldered the wires to them and now the laptop works perfectly. 15 minutes of work and I saved the laptop from going to the landfill dump.

-
Nice job James!
Used the Charge to fix the petcock on the mini ATV.
-
@sappyg said:
whew... busy day.
used the spirit to cut off several RG6 wires to roll them up nicely for the new homeowner. this was the only task the vic came up short. it took rotating the wire and making another cut.
used the pliers to poke out the dried mud in a water meter lid and then picked it up with the pliers to place it on the meter. (note to self, get another landscaper)
used the wire cutters to shorten up the low voltage wires for the garage door operator of that home.
used the pliers to pull a nail out of my rear tire so i could plug it (note to self: need to buy more rubber cement)
used the flat head or the can opener to screw on an outlet cover for a microwave.
used the phillips to tighten up a base door stop.
used the PE blade to cut out some glue left on the carpet (still can't figure out how that got there)
used the phillips again to remove the base mount of a towel ring in the master bath of the 1st home. got ticked off b/c i could'nt remount it b/c of the POS mounting screws the installer used.
finally, used the pliers again to repair a sprinkler head that popped off of its base on this home.
i washed out the grit from the water meter lid in the kitchen sink when i got home. steeled the PE blade... good as new. :sak:Thats what I like to see,a tool getting a real workout!!!

-
I've been helping a friend paint while I'm in town, so I have had the chance to test some of the Surge's capabilities. (It is a brand new tool, had it since saturday :D) Been prying paint cans open with the large flathead, pulling faceplates and other screws out of the wall with the bit exchanger. The bottle opener popped us open a few brews, and we called it a night.

-
Holy crap! I actually used tools today! For a real reason! Changed the passenger side mirror on the Camry, Blast for screws and the side anchors and a pocket widgy prybar for... prying!
Both tools performed admirably. :D
Also used the Leatherman rebranded Fenix L1T v2 and an LED Maglite 3D... :ahhh
At this rate I might actually justify having all these! -
used my spirits serrated knife, to cut washing line and garden hoses, i think i know why its dubbed the butter knife as it cut through the hose like a hot knife through ........ :D lol
-
@One Lame Frog said:
used my spirits serrated knife, to cut washing line and garden hoses, i think i know why its duded the butter knife as it cut through the hose like a hot knife through ........ :Dlol
I actually love the peanut butter spreader. :D
same here mate ive really started enjoying using this blade :)
-
Been rolling with the old Wave today and it started the day by opening a couple of exciting packages :D
One was my TerraLUX upgrade drop ins for a couple of Maglites and the other was a lovely old Orlik Tank lighter. The Orlik then got a little service with the help of the Wave and is working like a dream.
The TerraLUXs are in all in safely but I'm damned if I can find any AAA batteries to get the little one fired up ::)I have also packaged up the modding bits for Neil to play with :D
Off to the shops for me...
-
Need to see the lighter :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login