My 3DC
-
As long as you are baking the cakes at less than 150 C you should be okay! :ahhh
I also printed a bumper for my new DJI Neo. I don't believe it needs it, but all the cool kids are putting them on so I figured I might as well do it too.
I used the lightest of these ones figuring this is just an extra bumper on top of the existing factory bumpers. If it gets destroyed I may try a heavier version.
Def
-
Oops, forgot the pic.
Def

-
@Vidar said:
Flexible rubber version? Bend and bounce instead of breaking. Foam or 3D strusses?As I said, my printer doesn't support fancy materials for that kind of thing so I have just printed it in regular, hard PLA.
It should protect the camera somewhat, although to be honest I really don't feel like it needs it. I watched a video where a guy flew it repeatedly into trees, brick walls, concrete seawalls etc at speeds of around 45kph and the drone stood up to it. And, if the Neo does get damaged, I have the insurance and can replace it for about $20. I was more interested in seeing how well it printed, and it's got a few flaws. For example I think there was some of the other green blobbed in the head that came out because there were a few layers that didn't look right. I must have missed that the last time I cleaned the head?
I printed one for my father's Neo as well, and it came out much better. :D
Def
-
@Grant Lamontagne said:
It should protect the camera somewhat, although to be honest I really don't feel like it needs it. I watched a video where a guy flew it repeatedly into trees, brick walls, concrete seawalls etc at speeds of around 45kph and the drone stood up to it.Sounds like a drone adapted to my skill level! :ahhh
-
This one, oddly enough is well adapted to every skill level as it bypasses the weakest link. It eliminates the silly component between the remote and the ground.
Def
-
There is certainly a lot that needs bypassing or plain ignoring.. I would ask my wife if she agrees, but oddly she pretends not to hear me.
But wait - the drone of that guy who hits all kinds of stuff was suicidal then?
-
Actually no.
There's more on this in the Drone thread in the Break Room, but in a nutshell, the new Neo is available for $200 USD and comes with several autonomous flight modes. No controller required. If you want it to follow you as you hike down the road, you select Follow Mode on the drone and it takes off and automatically follows you. It has six automatic modes including Follow, Dronie (drone starts on you then backs up revealing where you are), Rocket (same as Dronie but instead of backing away, the drone goes up and over you, looking straight down at you), Circle (it rotates around you at a fixed distance, keeping you center frame), Spotlight (like follow, but the drone remains in the same place, as if it was a camera on a tripod, but rotates to keep you in frame) and Direction Track, where it stays in front of you, flying backwards to keep you in frame as you walk.
Because it doesn't have sensors to avoid things (it will avoid objects in front of the camera as the visual tracking maps objects) it is designed to be quite robust, with enclosed/covered propellor blades so it is resistant to crashing. Add in that it only weighs 135g, and it doesn't really develop a lot of force on impact. If there isn't much force on impact, there isn't much force to damage it.
Plus, DJI offers a service called DJI Care which you can activate within 2-3 days of buying the drone. This cost me about $40 CAD, but if I lose or damage the drone, DJI will replace it for a $20-25 deductible. That means that even though the drone is cheap enough to begin with, it is even cheaper to replace. That means that you are more likely to have it with you, use it and get cool shots you probably wouldn't want to risk a $2k drone on.
For example....
https://youtu.be/zFIWWM0Iv-U?si=wQzthrAScuxEaFQW
https://youtu.be/YVKhcPm3T5A?si=nfs8eCOBWEDzrwX2
Now these guys were probably well funded for this, but I think even I with our (very) limited budget would give this a shot if it was only going to cost me $25 to get up and running again.
Def
-
That is quite spectacular!
Sounds like an interesting drone. I've been thinking about a light weight one to get some new photo/ video angles and avoid having to go to unwelcoming places myself. (Well, more like deciding before going/ climbing/ crawling if it looks worth it or not).
-
The Neo might be right for you. They just released a new package which is $710 CAD that might be of interest. It comes with the drone, motion controller (like a flight stick), goggles (for first person view or FPV flying), three batteries and a charger. Honestly, that's probably the package you want if you are thinking of using it for scouting
Or, you could get the Fly More pack, which has a regular dual stick controller, three batteries, charger and drone.
Getting back to the importance of 3D design and printing, I recently came into possession of a Leatherman Fuse with a broken locking tab. This is a common enough problem and leaves me with a few choices.
1- send it in for warranty repair and probably get a Bolster or something back.
2- send it in for warranty repair, pretend it's sentimental and ask them to fix it rather than replace it.
3- sell it to a modder for parts.
4- try and copy the original design in Fusion and see about printing a new one. If it fits, see about getting the design printed at a commercial printer, possibly out of something fun like titanium.
Naturally I am considering the most awkward option of designing and printing a new tab. I have done most of the design so far, I just need to print one and see if it is actually close enough, then modify the design etc until I get it perfect.
If I can manage that, I might look into getting a few replacements made in some fancy metal- I could probably sell them by the dozen and retire off the proceeds, because who wouldn't want to convert their Blast or Fuse to having titanium locks? :D
Def

-
If you could redesign away the need for those protruding pins, (say by making a hole instead and later putting in pins), that would make that part easier to make with a variety of technologies.
-
Yeah, that pin is exactly what always breaks on these. A bar would be a good idea.
I'll have to check and see if there is enough space to make a decently reinforced slot for a bar.
Def
-
I may or may not have been playing around with a certain something yesterday....
Took me two iterations to get the scale right (until I got around to measuring
) then one more iteration to get the clearances right, but I now have a functional plier head.It still needs some work- for example I have already cut back the plier handle attachment points a bit to allow the jaws to open a bit wider, and I think I may change the removable cutter section and replace it with a built in set of anvil cutters. Either that or I will need to reconfig the head to make more space as the current cutter slot is pretty small.
All in all, not a bad result for a first (fourth) attempt.
It's also the first time I have (successfully) designed and printed a multi-component thing that actually fit together, so I am a bit proud of that.

Def

-

Any particular plan with those? Going metal with them too?
I think the print would be stronger if the infill was connected to the outer skin?
-
So far just a proof of concept and refining the design to see if I can do it, how it would work etc.
Strength and metal etc can wait till I get it to a point where it's worth the extra strength of extra plastic or metal! :D
For now, I am just playing.
Spoiler:
Or am I? >:DDef
-
Not my design, but I printed a box for my Neo the other day.
It kind of maxed out my printer and had to be rotated 45 degrees to fit on my print bed, but it got there. Oh yeah, and I had to print the lid and the box separately because they wouldn't both fit on the bed at the same time.
In the end it is great- I couldn't be happier with it. It keeps my Neo safe and sound when rattling around in my backpack. I didn't print the magnetic version, so I just use a rubber band to hold it closed.
Def


-
Handy drone that one - and even more so with travel protection!
-
I tried using some Anycubic Craftsman resin that had expired its best before date by over a year. It seemed a bit more runny than usual, and seemingly with more rounded details than a fresh batch would give. (Or that model has less sharp edges than I usually do). But overall it did fairly well I think - one try, all the usual settings, usual washing procedure. One could possibly do better by adjusting some of those to take old resin into consideration.
So there is hope for old resins too it seems.





-
All of that post processing/UV stuff is kind of off putting (for me at least) with resin printing, however those parts look absolutely amazing. The detail and perfection is far beyond the filament printing I am doing, so maybe I will have to get over my paranoia!
Which machine are you using, and would you recommend it or suggest something else?
Did I say those parts look amazing? Because they absolutely do!
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
