How many screwdrivers does one multitool need?
-
Here is the Top Ten list according to CoPilot AI:
Phillips #2: 3.5 mm
Flathead: 3/16 inch (4.8 mm)
Phillips #1: 2.5 mm
Torx T15: 4.5 mm
Torx T10: 3.9 mm
Phillips #3: 5 mm
Flathead: 1/4 inch (6.4 mm)
Torx T20: 5.4 mm
Pozidriv PZ2: 4.5 mm
Hex (Allen) 5/32 inch: 4 mm
Would there be anything missing from that list that anyone else needs?
And yes, for the Canadians out there, I did ask it for a Canadian version of the list, figuring the Robertson bits might be a bit more prevalent, but overall it isn't much different:
Phillips #2: 3.5 mm
Flathead: 3/16 inch (4.8 mm)
Phillips #1: 2.5 mm
Torx T15: 4.5 mm
Torx T10: 3.9 mm
Phillips #3: 5 mm
Flathead: 1/4 inch (6.4 mm)
Robertson #2: 2.8 mm
Hex (Allen) 5/32 inch: 4 mm
Torx T20: 5.4 mm
Def
-
I'm with Powernoodle on this one Def. A Cybertool is a great compromise given the number of Torx bits out there.
-
I'm somewhat surprised that I haven't encountered a huge variety of screws at work. For the most part, the Phillips and large flathead on my ST300 will handle things nicely. A T20 and T25 will take care of the rest.
At home, it's almost exclusively the common Phillips sizes and a few flatheads.
-
@Grant Lamontagne said:
Would there be anything missing from that list that anyone else needs?That sounds like a plausible top 10. From memory I also fairly frequently encounter Torx T25 and Torx27, and a lot of Hex in all sizes but mostly metric. Maybe Hex is less popular where CoPilot AI is consuming data. And also some very wide and thick flat driver - coin drive - on various camera and light gear. And PH/PZ 0 and 00 comes up surprisingly often. And once in every full moon I encounter one these so called safety torx with a pin in the middle.
I also have a PH4 bit laying around here for that one special freak thing that needed it one time.
-
FWIW, here’s ChatGPTs list:
1. Phillips #2 2. Flathead 1/4” 3. Phillips #1 4. Torx T15 5. Flathead 3/16” 6. Torx T20 7. Hex 1/8” 8. Flathead 1/8” 9. Phillips #3 10. Precision (Jeweler’s) ScrewdriversIt strikes me that, outside of the hex, pozidrive, and some Torx, a basic Spartan, Tinker, or Sportsman is capable of handling just about everything on these lists.
In my years carrying the Spartan, Climber, and close relatives (usually with the mini-driver), about the only screws I can recall encountering in the wild with any frequency that were a problem were deeply recessed Phillips screws.
-
@Vidar said:
That sounds like a plausible top 10. From memory I also fairly frequently encounter Torx T25 and Torx27, and a lot of Hex in all sizes but mostly metric. Maybe Hex is less popular where CoPilot AI is consuming data. And also some very wide and thick flat driver - coin drive - on various camera and light gear. And PH/PZ 0 and 00 comes up surprisingly often. And once in every full moon I encounter one these so called safety torx with a pin in the middle.I also have a PH4 bit laying around here for that one special freak thing that needed it one time.
I have a 25mm socket for exactly the same reason. I needed it once to change the oil in my Jeep and had to run out and buy one.
Then realized that the oil, filter and proper disposal cost just as much as going to a Mr Lube and getting it done, and it's a lot less hassle for them to do it.

I also agree that recessed screws are the Kryptonite for a lot of multitools.
Def
-
Gonna agree w/ a lot of others and say a #2 Phillips and a largish flathead (as much for scraping/prying than screwing) will probably serve about 80% of the time. Add in a smaller flathead to get up to 90%, followed by a #1 Phillips. Anything past that and you're getting into speSmurfpillst territory, rather than day to day.
-
Being a response grandpa means changing the batteries on the kids toys. The Vic 58mm combo tool
Is the most used screwdriver that.i own. -
I want all the sizes :ahhh I am surprized T25 isn't on the lists ??? I use that size of Torx more than any other
I carry many different size drivers with me and encounter many different kinds of fasteners on a construction site
I am sure there are some I carry that have probably never been used though
:D -
@Poncho65 said:
I want all the sizes :ahhh I am surprized T25 isn't on the lists ??? I use that size of Torx more than any other
I carry many different size drivers with me and encounter many different kinds of fasteners on a construction site
I am sure there are some I carry that have probably never been used though
:DA T25?
What are you using that on regularly? I think I have only seen those in cars.
Def
-
I use T25s to remove the felt things that are underneath the engines of certain Fords. A T20 is useful when inspecting the air filter in a large Transit van, as the windshield washer reservoir neck (which I pivot out of the way to assist in removing the top of the air box) is held in place with one.
And while I'm wishing, nut drivers in 7mm, 8mm, and 10mm would be nice.

-
@Grant Lamontagne said:
What are you using that on regularly? I think I have only seen those in cars.Around here lots of construction wood screws are T25 as they are nice to use with a powerdrill. I also encounter them on various machines. Pretty much the same places where I find Hex screws - although maybe less so for things meant for grimy environments.
-
I am in love with Robertson. I only buy Roberston screws, etc. I have had bad luck with Phillips stripping on me. Don't get me started with flatheads.

-
@Chako said:
I am in love with Robertson. I only buy Roberston screws, etc. I have had bad luck with Phillips stripping on me. Don't get me started with flatheads.
I'm another Robertson fan, with the caveat that you should have an (appropriately adjusted) adjustable clutch on your cordless driver to save your wrist when a tough screw bottoms out and suddenly stops turning. I've also tried torx screws, but just prefer Robertson.
-
Just you wait until you are in a tight spot and your face is right next to the drill! :ahhh
Don't ask me how I know that....

@Farmer X said:
I use T25s to remove the felt things that are underneath the engines of certain Fords. A T20 is useful when inspecting the air filter in a large Transit van, as the windshield washer reservoir neck (which I pivot out of the way to assist in removing the top of the air box) is held in place with one.And while I'm wishing, nut drivers in 7mm, 8mm, and 10mm would be nice.

As for the T25, I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?
Def
-
Robertson should have been the common one back in the day. Instead we got plenty of other "standards" with various strong and weak points, and no strong single standard. Just to make it even greater even the standards are slightly different around the world - and then there is imperial and metric..
@Grant Lamontagne said:
As for the T25, I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?Not as a top 6, but somewhere after that? With bit holders that is more feasable.
@Farmer X said:
And while I'm wishing, nut drivers in 7mm, 8mm, and 10mm would be nice.
Plenty of those around and even the cheap ones are good. Very handy for power drills!

-
@Grant Lamontagne said:
I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?T20 and T25 are the Torx sizes I commonly run across on the lube rack. The T25s are on the underside of the vehicle, and they can be a bear to remove. I don't know if I'd trust a multi to break torque on them. But a T20 on a multi? Hell yes! That could save me a few seconds of grabbing the plastic tool box and pulling a T20 out of it.
On that note, in the plastic tool box is a "mechanic's tool kit" that doesn't include any pliers. How and why?
Good thing an ST300 and the cheapo slip joint pliers I found in the street have me covered in the pliers department.Of cours, all that comes with a caveat...for now.
-
I'm a bit surprised that no one mentioned T6/T8, as there are plenty of knife people here. For me, they come right after Phillips and flatheads (and possibliy a 4mm hex for all the Ikea furniture) to adjust a pivot or tighten a pocket clip.
-
Myself I use a flat driver and a Phillips 1 and 2. I can occasionally need a Roberson drive or maybe a large Torx. But at most a T6/T8 for taking my gadgets and gizmos apart.
Sent from my SM-G996U using Tapatalk
-
My Vic Explorer Plus handles the large majority of my screwdriver needs. The Rambler handling the rest…with a very few exceptions.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



