Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Clock repair

Scheduled Pinned Locked Moved Watch it!
10 Posts 1 Posters 1.6k Views
  1. Home
  2. Non Tool Forum
  3. Watch it!
  4. Clock repair
Clock repair
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Farmer X Offline
    Farmer X
    Posts: 13,847
    Farmer X Offline
    Farmer X
    wrote on last edited by
    Quote Reply

      This question might not be pertinent to a watch, but a clock is a timepiece, so this seems a decent enough spot for it.

      That said, my neighbors have a rather nice Bulova wall clock. The lady of the house said a new battery was put in, and the clock just stopped working. I took a look at it and noticed a little verdigris on the positive battery terminal, but I am hesitant to tear too much into it, for what should be obvious reasons.

      The internals were more complex than I expected, with a circuit board visible. I have no clue what might be at issue here. Perhaps one of y'awl has successfully repaired a clock with such an issue?

      Thanks in advance for any help! :cheers:

      1 Reply Last reply
      • powernoodle Offline
        powernoodle
        Posts: 7,103
        powernoodle Offline
        powernoodle
        wrote on last edited by
        #1 Quote Reply

          You can try carefully cleaning the battery contacts with something slightly abrasive like a magic eraser. It could be as simple as that. Anything beyond that is above my pay grade.

          :salute:

          1 Reply Last reply
          • IMR4198 Offline
            IMR4198
            Posts: 6,451
            IMR4198 Offline
            IMR4198
            wrote on last edited by
            #2 Quote Reply

              Verdigris is non-conductive, so that may be all the problem. You can clean off verdigris with a drop of alcohol on a Q-tip. Might need to try another battery. I assume it is a AA? Best wishes. G
              :D

              1 Reply Last reply
              • Farmer X Offline
                Farmer X
                Posts: 13,847
                Farmer X Offline
                Farmer X
                wrote on last edited by
                #3 Quote Reply

                  There wasn't much verdigris, and it wasn't on the point where the battery contacts the terminal. Surprisingly, the clock uses a single C battery.

                  1 Reply Last reply
                  • IMR4198 Offline
                    IMR4198
                    Posts: 6,451
                    IMR4198 Offline
                    IMR4198
                    wrote on last edited by
                    #4 Quote Reply

                      If the clock case is attractive, I have seen people replace the entire clock mechanism with a new electric unit. Not original of course, but functional. Usually don't see verdigris without an acid or dampness reacting with copper (or a copper alloy like brass or bronze.) Did an old battery burst in this clock? Best wishes. G
                      :think:

                      1 Reply Last reply
                      • AzteCypher Offline
                        AzteCypher
                        Posts: 4,051
                        AzteCypher Offline
                        AzteCypher
                        wrote on last edited by
                        #5 Quote Reply

                          Magic eraser on the contacts, then wipe with alcohol.

                          If you're up for it, open the back to see if there's any more corrosion from that contact reaching out to the circuit board. I've also used a small brass brush to clean off the contacts.

                          1 Reply Last reply
                          • Farmer X Offline
                            Farmer X
                            Posts: 13,847
                            Farmer X Offline
                            Farmer X
                            wrote on last edited by
                            #6 Quote Reply

                              I didn't see any evidence of a battery bursting. And since Gary mentioned it, I wonder if it had the movement replaced at some point in its life. There is a label from a clock repair place in Ann Arbor on the back, so it seems plausible. If there's any way for me to open the case without risk of damage, I'll check the circuit board(s), too. Thanks again, y'awl! :cheers:

                              1 Reply Last reply
                              • nate j Offline
                                nate j
                                Posts: 6,226
                                nate j Offline
                                nate j
                                wrote on last edited by
                                #7 Quote Reply

                                  @IMR4198 said:
                                  If the clock case is attractive, I have seen people replace the entire clock mechanism with a new electric unit.

                                  I have done this successfully. The clock in question isn’t particularly fancy, but is of sentimental value to my wife as it belonged to her grandparents.

                                  It isn’t particularly difficult and the single AA mechanisms are inexpensive. Just be sure to check measurements before ordering.

                                  1 Reply Last reply
                                  • Farmer X Offline
                                    Farmer X
                                    Posts: 13,847
                                    Farmer X Offline
                                    Farmer X
                                    wrote on last edited by
                                    #8 Quote Reply

                                      If a single C mechanism can be found cheaply enough, that might be a good way to go. Thanks again to awl for the help!

                                      1 Reply Last reply
                                      • nate j Offline
                                        nate j
                                        Posts: 6,226
                                        nate j Offline
                                        nate j
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Not sure it would have be C battery powered.

                                          This is what I got:

                                          EMOON Clock Movement Mechanism... https://www.amazon.com/dp/B07T7W75GQ?ref=ppx_pop_mob_ap_share

                                          There are a lot of similar ones out there. The main things are to make sure the mechanism will fit inside your clock, you choose the right shaft length (cue jokes), and there is at least one set of included hands that will be appropriate lengths and match the clock.

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Non Tool Forum
                                          3. Watch it!
                                          4. Clock repair
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0