How many screwdrivers does one multitool need?
-
I am in love with Robertson. I only buy Roberston screws, etc. I have had bad luck with Phillips stripping on me. Don't get me started with flatheads.

-
@Chako said:
I am in love with Robertson. I only buy Roberston screws, etc. I have had bad luck with Phillips stripping on me. Don't get me started with flatheads.
I'm another Robertson fan, with the caveat that you should have an (appropriately adjusted) adjustable clutch on your cordless driver to save your wrist when a tough screw bottoms out and suddenly stops turning. I've also tried torx screws, but just prefer Robertson.
-
Just you wait until you are in a tight spot and your face is right next to the drill! :ahhh
Don't ask me how I know that....

@Farmer X said:
I use T25s to remove the felt things that are underneath the engines of certain Fords. A T20 is useful when inspecting the air filter in a large Transit van, as the windshield washer reservoir neck (which I pivot out of the way to assist in removing the top of the air box) is held in place with one.And while I'm wishing, nut drivers in 7mm, 8mm, and 10mm would be nice.

As for the T25, I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?
Def
-
Robertson should have been the common one back in the day. Instead we got plenty of other "standards" with various strong and weak points, and no strong single standard. Just to make it even greater even the standards are slightly different around the world - and then there is imperial and metric..
@Grant Lamontagne said:
As for the T25, I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?Not as a top 6, but somewhere after that? With bit holders that is more feasable.
@Farmer X said:
And while I'm wishing, nut drivers in 7mm, 8mm, and 10mm would be nice.
Plenty of those around and even the cheap ones are good. Very handy for power drills!

-
@Grant Lamontagne said:
I recognize that you guys are using them daily, but that seems like in a shop scenario where the proper tools are handy. Is this something that you would want on a multitool?T20 and T25 are the Torx sizes I commonly run across on the lube rack. The T25s are on the underside of the vehicle, and they can be a bear to remove. I don't know if I'd trust a multi to break torque on them. But a T20 on a multi? Hell yes! That could save me a few seconds of grabbing the plastic tool box and pulling a T20 out of it.
On that note, in the plastic tool box is a "mechanic's tool kit" that doesn't include any pliers. How and why?
Good thing an ST300 and the cheapo slip joint pliers I found in the street have me covered in the pliers department.Of cours, all that comes with a caveat...for now.
-
I'm a bit surprised that no one mentioned T6/T8, as there are plenty of knife people here. For me, they come right after Phillips and flatheads (and possibliy a 4mm hex for all the Ikea furniture) to adjust a pivot or tighten a pocket clip.
-
Myself I use a flat driver and a Phillips 1 and 2. I can occasionally need a Roberson drive or maybe a large Torx. But at most a T6/T8 for taking my gadgets and gizmos apart.
Sent from my SM-G996U using Tapatalk
-
My Vic Explorer Plus handles the large majority of my screwdriver needs. The Rambler handling the rest…with a very few exceptions.
-
I don't have the extended bit set, but for my everyday stuffs I find my Wave+ doing things just fine. The phillips/flat head bit is plenty good. The eyeglasses screwdrivers I use them too but less often.
When I really need screwdrivers with different heads usually I have dedicated screwdriver sets around so it's not a much of a problem for me. -
How many screwdrivers does one multitool need? All of them
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



