Show your slip joint's thread!
-
Nice

-
First off...put the Dremel down and back away slowly. :o
I'm old school and use flat stones. I re-profiled the secondary on a coarse side silicon carbide stone, holding the blade almost flat...raised a burr on one side, then the other. Then I ran it on the fine side of the stone.
Once that was done I used progressively finer wet/dry paper on a stiff rubber pad (not a mouse pad) to clean up and blend the shoulder of the secondary into a convex...followed by a stropping with black then green compound.
Unless the blade gets abused, stopping will keep it sharp for a long time before having to resort to stoning again…and usually a fine grit stone will do the job.
I test my edges on leather scraps and by making wood shavings. I find paper cutting and shaving hair deceptive...it doesn’t give me a true indication of how well the edge will cut in thicker materials or how well it will carve wood.

-
Ok, latest GEC acquistion just came in this morning. This one a bit unique, Great Eastern Cutlery #23 pattern "Left-Hand" Pioneer Jumbo Trapper.


Finally got around to getting one. I'm not left handed but it doesn't matter, you don't see many companies doing a lefty slipjoint. The only difference between these and a regular Pioneer is that the Spey and Clip blades have swapped sides. The shield is still on the same side as the "Right-Handers".
These are of 2007 manufacture and are the Pioneer #23 pattern at 4.5" closed. Mine is serial number #10 out of the run. They are GEC brand with the Cyclops Steel Works blade etch making them 440-C bladed. Typical GEC construction with nickle/silver bolsters, brass liners and pins, and stout backsprings.
Fit and finish is near flawless, one minor issue I did find though is in the polish of the blades. On this one the polish is a bit hazy, kinda like it wasn't completed......like the person doing these didn't spend enough time on the buffer. Nothing big as it is consistant throughout both blades, just not as nicely done as my others. Outside of that this thing is flawless and gap free.

As to the edges, one thing I have heard people complain about on GEC's recently. This one, like my others, have sharp usable edges. They ain't scary sharp but will remove arm hair......just not as effortlessly as some of my other slips. But they ain't butter knife dull.
The bone on this one is that River Blue Bone. Very nice color, kinda deep in hue but does lighten up a bit in areas. The jig is like a Stag Bone jig, really nice.

I ordered this one from Mike over at CollectorKnives.net, and along with it I ordered one of the new GEC Blade picks in Buffalo Horn.........


.........real nice little piece with a slim profile. Made of stainless with slim Buffalo Horn slabs pinned on both sides. The scales on this have nice angular edges all the way around. I didn't get this one to use as I don't have problems getting my GEC's open, I got it for my collection to go along side my Buffalo Horn and Ox Horn Pioneers. These picks are 3 3/8" long and at their thickest point, across the scales, they are only about 3/16" thick.
2xTap

-
Here's my fav slip joint ATM thank ringzero


I decided to de-badge it >:D the etching on the blade gone!


And a not so great tip for some but! it's how I like to EDC my knives why? well it could afford me seconds or even minutes depending on the intellect of a potential assailant(should they want to turn my knife against me)
also it works great when you have little enquiring minds in your family 

-
The Fallkie U1 could never be called pretty, but it's non threatening looking and very functional. Very well put together too.
-
@Magic Bus said:
The Fallkie U1 could never be called pretty, but it's non threatening looking and very functional. Very well put together too.I didn't get on with it personally, lovely looking little thing but not really comfy in my hand.
-
@Magic Bus said:
The Fallkie U1 could never be called pretty, but it's non threatening looking and very functional. Very well put together too.
I didn't get on with it personally, lovely looking little thing but not really comfy in my hand.
I know you had one for a short time, but got the UKP now, right? That's one I'm interested in after seeing Dunc's. It's on the list when funds allow.
-
Hoping to do a vid on the case sodbuster jr soon i.e slash the bottle or bottles! test :D man! this things sharp :D
-
what's wrong with a slippy?
like I said they can be used in the same way

slip joints forever :D BTW don't try this at home until you understand the slip joint :D
http://www.youtube.com/watch?v=nvRiIp2iMugYes I know you'll yawn ahh! and Yes I should yawn for the lack of responses :ahhh but I wont I would just like to add:don't try this at home without supervision :D I'm kidding guys break a leg :)
-
Nice job!

Is the Katana for stiring your tea ??? :D
-
APPLAUSE...

That can won't be bothering anyone anymore... :D -
For fun as I like this knife tomorrow comes the 3ltr bottle (PLASTIC) test,hmm like the sodbuster's worried? :D stay tuned

[EDIT]now where's my dremel :D
-
A couple of nice slippies added there.

-
Got this one in yesterday. Not my favorite handle material but it is a Gunboat! It was on auction and bidding was running low so I threw in a low bid and waited. My patience (something I am not known for) paid off. I figured I would be outbid as Case Gunboat Canoes can be quite pricey but only one other person bid after me and mine was a bit higher still.
Case "Vintage Pattern Series" Gunboat Canoe in Periwinkle Bone:



I was surprised that I won it as my max bid was rather low, but I won it even lower than that. It's NIB and I paid a mere $59.00 for it!!!!!!! :o
Just took some quick pics of it as I took it out of the box, haven't had a chance to really clean it up yet so there is some tarnish on the liners and the bolsters look a little hazy in the pics. In person though the Bone ain't as bad as I thought. In pics it just didn't look all that good to me, but in hand it's not bad. But either way it's my favorite slippie pattern......and at $59.00 it was an absolute steal.
2xTap

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
,I have a dremel
:D