Looking for edc multitool recommendations.
-
My very first thought was the old Wenger Ranger 130 that has folding shears
I think it’s the Ranger 174?? I also think it has Philips on the backside too
If you check sakwiki you’ll know for sure. I don’t know if Victorinox released the same version too?? -
@tosh said:
My very first thought was the old Wenger Ranger 130 that has folding shears
I think it’s the Ranger 174?? I also think it has Philips on the backside too
If you check sakwiki you’ll know for sure. I don’t know if Victorinox released the same version too??Victorinox made model with folding scissors (RangerGrip 71 Gardener) but it has corkscrew instead phillips but on orginal Wenger has phillips on backside (Ranger 172 - Gardener)
here is my Vic Delemont RangerGrip 71 Gardener
[attach id=0 msg=2545906]

-
@fullbreakfast said:
The flat Phillips on the Micra is indeed not bad, I found the main problem with it was I would forget it was there and not use it when I could have. The only downside I can see with it for current purposes is that sometimes those battery compartment screws are recessed in quite small holes and it might not fit. But would be just fine 95% of the time.This is where I eat crow. Because I had to charge the batteries in a stupid Brio locomotive where the screw is down the chimney hole, which is both narrow and surprisingly deep.
Troika mini tool pen from my EDC pouch? No, too short:

Inline Phillips on my Explorer almost reached, but got too thick too soon to get right down there:

Hoto precision driver? No chance:

Cybertool bit holder is too big:

So is the Wiha 4mm adpater:

Micra for the win!

I've also got a set of proper precision screwdrivers with long thin blades, of course. But I view using those as strictly cheating.
-
@fullbreakfast said:
This is where I eat crow. Because I had to charge the batteries in a stupid Brio locomotive where the screw is down the chimney hole, which is both narrow and surprisingly deep.Troika mini tool pen from my EDC pouch? No, too short:

Inline Phillips on my Explorer almost reached, but got too thick too soon to get right down there:

Hoto precision driver? No chance:

Cybertool bit holder is too big:

So is the Wiha 4mm adpater:

Micra for the win!

I've also got a set of proper precision screwdrivers with long thin blades, of course. But I view using those as strictly cheating.
Curious if the Vic 58mm combo tool would have gotten this done?
-
@fullbreakfast said:
I've also got a set of proper precision screwdrivers with long thin blades, of course. But I view using those as strictly cheating.On no other forum in the world would using the right tool for the right job be considered cheating! :D
Good for you, getting the job done in the least convenient (but coolest) manner possible!

Def
-
@nate j said:
Curious if the Vic 58mm combo tool would have gotten this done?Good question, I didn’t think of that at the time. Even though my Vagabond was sitting in my work bag right by me. But I’ve checked, and yes it does the job quite nicely.
It just goes to show, a SAK can always do the job, just not necessarily the one you have in your hand.
-
@fullbreakfast said:
Good question, I didn’t think of that at the time. Even though my Vagabond was sitting in my work bag right by me. But I’ve checked, and yes it does the job quite nicely.It just goes to show, a SAK can always do the job, just not necessarily the one you have in your hand.
Nice, thanks!
I’ve found the combo tool on my keychain Rambler very useful; well worth the upgrade over the Classic.
-
I also tried the little Klein 32600P precision screwdriver, that uses their 3.5mm bits, on the Brio locomotive test. I don’t think any 4mm bit driver would get down there (unless you had extra-long bits…hmmm) but the Klein can. That 0.5mm making all the difference here.
Maybe the use of this non-standard size for precision bits by Klein was not so daft, after all.
-
Micra gets my vote and recommendation!
-
One tool I don’t think was mentioned but you might want to try is Nextools Mini Sailor Scissors or Mini Flagship. The scissors on both of those are on par with the Micra and they have a phillips.
-
Save your time, buy SwissTool Spirit.
-
Another option is the Gerber Armbar. But I didn't like it at all, either for the build quality or the weight. Perhaps the Leatherman Micra and a ratchet with extended bits are your best option.
-
Not all multitools are the same, so it really depends on what you’ll be using it for the most often. Think tightening screws, opening packages, cutting fishing line, etc. Then find one that offers tools for all of those tasks, or at least as many as possible. Keep in mind that bigger tools pack in more features, but smaller ones are way easier to carry. I prefer ones that are small enough to fit in my pocket.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
