Rebar Owner's Club (pic heavy)
-
Thanks chip, that's a comprehensive write up and it's made me even more tempted. There's a shop around the corner from my work selling the ss version for forty quid so I might just cave eventually
-
At £40 it’s hard to pass up, but make sure it’s the updated version to avoid the tip of the blade biting you when using the pliers.
-
@chip said:
At £40 it’s hard to pass up, but make sure it’s the updated version to avoid the tip of the blade biting you when using the pliers.Thanks for the 'tip'. See what I did there.
Is there any way to tell which version it is other than opening it up?
And if it is the old version can the issue be remedied by reprofiling the blade?
-
They redesigned the blade not only to sit the tip lower in the handle but to remove the few degrees of travel from closed it could move freely, that combined with the blade shape allowed the problem.
I don’t know if this was a problem with all of the original design tools or just a few. But it was enough to prompt a revision. I personally prefer the look of the revised blade shape but that’s horses for courses.
But to answer your question I don’t know if you could tell without handling it.
-
@chip said:
They redesigned the blade not only to sit the tip lower in the handle but to remove the few degrees of travel from closed it could move freely, that combined with the blade shape allowed the problem.I don’t know if this was a problem with all of the original design tools or just a few. But it was enough to prompt a revision. I personally prefer the look of the revised blade shape but that’s horses for courses.
But to answer your question I don’t know if you could tell without handling it.
Thanks. I might have to pop over to the shop and do a bit of handling like I know what I'm doing then
-
Msgs
The 2nd gen BOND has one key feature that tells you it is a Gen 2
On the blade handle side, no pocket clip holes, the handle has no cutout or punch through.
[attach id=0 msg=2562793]
Top is a gen 2
Bottom is a gen 1
The punch tap holds the blade higher for nail Nick to be accessible.
-
@LoopCutter said:
MsgsThe 2nd gen BOND has one key feature that tells you it is a Gen 2
On the blade handle side, no pocket clip holes, the handle has no cutout or punch through.
[attach id=0 msg=2562793]
Top is a gen 2
Bottom is a gen 1
The punch tap holds the blade higher for nail Nick to be accessible.Thank you Sir

-
Looks like the shop around the corner is selling Bond version 1.0 off cheap.
I think I will leave my money in my wallet for now and apologise to my Rebar for looking at other shiny tools. I hope they forgive me -
Rebar helped out with a few tasks at work today - I used the large flathead, Philips and serrated blade as well as the pliers (to grip some pesky pigtails)



-
-
So is my Swisstool Mags!
It's great seeing your Rebar doing what it was meant to do! I've always liked mine. It's a ton of utility packed into a compact package. -
@Barry Rowland said:
So is my Swisstool Mags!
It's great seeing your Rebar doing what it was meant to do! I've always liked mine. It's a ton of utility packed into a compact package.Agreed, following this thread has almost driven me to free my coyote tan rebar from the cupboard where I imprison my collection after an initial inspection for the rest of time.
-
I have three long time REBAR users, the first a SS, then a COYOTE, and the the BO.
ALL performed as intended and never disappoint.
This last year I added a Burnt Seinna, but not had to put to any hard use as I am retired and always seen to reach FF or first love the SS.I envy MAGS, getting to use his for real work, that I ALMOST, almost wish I could wake to. N early alarm and go to o a job each day just to show off my REBAR acting as an extension of my fingers when extracted f get on its belt sheath.
😉 -
@LoopCutter said:
I have three long time REBAR users, the first a SS, then a COYOTE, and the the BO.
ALL performed as intended and never disappoint.
This last year I added a Burnt Seinna, but not had to put to any hard use as I am retired and always seen to reach FF or first love the SS.I envy MAGS, getting to use his for real work, that I ALMOST, almost wish I could wake to. N early alarm and go to o a job each day just to show off my REBAR acting as an extension of my fingers when extracted f get on its belt sheath.
😉I feel very lucky to work a job where I can use a multitool every day.
Here's my Rebar in its weekend configuration, with a few other tools, and my lovely Opinel no.7. Today, at home I changed the plug on my partners car battery charger and the wrenches to remove the battery from her car.
-
Mags, that's about as close to a perfect at home kit as I can think of. You've got about everything covered. I like that No. 7!
-
@Barry Rowland said:
Mags, that's about as close to a perfect at home kit as I can think of. You've got about everything covered. I like that No. 7!Thanks Barry.
Used the Rebar large flat driver to open some paint for the uboat

-
Looking great with those kits, mags

-
What color coat is the boat being prepared to receive?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
