MP600 pliers became really stiff after 1 use
-
I bought this MP600 never used, still in the packaging, second hand, with the intention to use it for, say, tasks that I would not use more expensive MT for.
It was working correctly, the pliers were loose like, say a Rebar (there is no spring on it either), and after literally 20 seconds of using it to turn something, not even in a weird way for the pliers, the pliers are very stiff to close.
I used it in the same plane as the tools if you prefer, I didn't twist the tool lengthwise.
To give you an idea of how stiff it became to close, I have to put the weight of 2 other MT at the end of the handle, literally 1 CenterDrive and 1 Rebar.
I'm a bit disappointed right now and I'm wondering if it can be fixed. Is your MP600 or similar Gerber tool without a spring in the pliers very loose or a bit stiff ? -
So sorry to hear that, as the MP series tends to run on the loose side. Out of over a dozen I have, two were stiffer (but not so as to need other tools to pry open/close )than the rest, and with use have been better. Try to work them with a commercial loosener or a mixture of ATF/acetone, or valve lapping compound; once loosened, clean thoroughly and lube as usual. Hope it voes for the best, as those pliers head tend to be pretty tough.
EDIT- Rereading, and seeing that the tool is new, perhaps try to exchange it and if it fails or is not as feasible, then try as I said earlier
-
@Juan el Boricua said:
So sorry to hear that, as the MP series tends to run on the loose side. Out of over a dozen I have, two were stiffer (but not so as to need other tools to pry open/close )than the rest, and with use have been better. Try to work them with a commercial loosener or a mixture of ATF/acetone, or valve lapping compound; once loosened, clean thoroughly and lube as usual. Hope it voes for the best, as those pliers head tend to be pretty tough.Just to clarify, if I hold the pliers open in the vertical plane, hold the lower handle horizontally, I have to put about the weight of two multi tools on the end of the top handle to get it moving (i.e defeat static friction)
But by itself the handles don't move with gravity alone.Another data point:
the outer hinge, i.e the pivot from the body of tool, is not the one being stuck, because it's moving first when I try to close the pliers.
I know it's the pivot from the moving pliers that is sticky.I assume something must have moved at the first real effort on the pivot - I used some force to close them, because it' s supposed to handle it.
I played with it for 1 day lightly and it was behaving normally if that helps for the diagnosis.
I can't really exchange it.
I bought it from someone second hand, but it was clearly new and never used. -
**
I know it's the pivot from the moving pliers that is sticky.**Yes, this is where they're usually stiff. Might have somthing from the casting or swarf around it that got caught; try the valve lapping. A little goes a long way!
-
@Juan el Boricua said:
**
I know it's the pivot from the moving pliers that is sticky.**Yes, this is where they're usually stiff. Might have somthing from the casting or swarf around it that got caught; try the valve lapping. A little goes a long way!
Can you elaborate just as little on valve lapping.
I'm not a mechanic, I don't really connect it to improving the pivot. -
You could start with a spray lube like WD-40 or similar and really blast the pivot so it gets in there between the two halves of the pivot. Then work it back and forth a zillion times. Then repeat.
As for valve lapping, "valve lapping compound is a paste composed of abrasive grits—typically silicon carbide or aluminum oxide—mixed into a grease-like or water-based binder. It is designed to cut, grind, and polish metal surfaces, such as engine valves and seats, to ensure a perfect, airtight seal."
So the WD-40 or similar could be a baby step to maybe mechanically remove any gunk from the pivot. And see how that goes. The valve lapping (or similar abrasive compound) might be phase 2 if you don't get any love from phase 1. The point there would be to work it into the pivot, then work the pivot back and forth a zillion times, to basically polish the mating surfaces.
Consider this just part of the "fun" of getting to know your MP600. You'll get to the finish line one way or the other.

-
@xl said:
Can you elaborate just as little on valve lapping.
I'm not a mechanic, I don't really connect it to improving the pivot.I can try for sure! Valve lapping compound is a runny paste used durimg assembly of engine heads, especially the valves, since it is is used to grind and polish abrasions and blemishes from the machining of valve and seats, to make an airtight seal between metals. It will be used to help polish smooth the inside of the pivot; use a toothpick to force the paste between the pliers half, as seen from either the top or bottom end, about half way the circumference. Open and close the pliers; they might feel worst at first, but should gradually loosen as the surface is polished. Do stop "right before you think its OK" (this can only be explained by feel, sorry), as when you clean the pivot it should feel fine then. Dry, and lube with mineral oil or whatever you preference is.
-
@Juan el Boricua said:
I can try for sure! Valve lapping compound is a runny paste used durimg assembly of engine heads, especially the valves, since it is is used to grind and polish abrasions and blemishes from the machining of valve and seats, to make an airtight seal between metals. It will be used to help polish smooth the inside of the pivot; use a toothpick to force the paste between the pliers half, as seen from either the top or bottom end, about half way the circumference. Open and close the pliers; they might feel worst at first, but should gradually loosen as the surface is polished. Do stop "right before you think its OK" (this can only be explained by feel, sorry), as when you clean the pivot it should feel fine then. Dry, and lube with mineral oil or whatever you preference is.Thank you
Problem solved.
I applied some kind of liquid degreaser / cleaner (not WD 40 but something similar) , then opened and closed it repeatedly while watching a movie. Probably a thousand times or something.
At some point it became loose again.
I'm so relieved, I feared it was going to just collect dust in a drawer. -
Glad you were able to fix it, and here's to hoping you like it as much as I do mines; they're good workhorses to have around.
Pictures of it would be nice ...
:D :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login