Hello Sailor! Marlin Spike/Rigging Knife Challenge - August 2026
-
Day 18
A sailor's friends.

-
Day 18
An early/extra unused picture I took for the 'Spork off' thread. The final pic I chose had more spork and no Skipper, so you get this one..jpg)
-
Day 19

-
@AzteCypher said:
That's a good looking RR nate!
-
Day 19 of 30
Today no use but its there if i need it
[attach id=0 msg=2585172]

-
Well, I settled in on 12 inches on the half round braid, for my lanyard. However, I was interrupted by an employee from the United States Postal Service, with a package.
Another Barlow, for next months Barlow Challenge.
Rough Rider with the CASE configuration.
-
Day 17
Marbles Rigging Knife, with all the tools.

-
<u>Day 199</u>
Just mail call today.

-
Day 20
Box opened with the flat driver just to see how it’d go, worked ok, no replacement for a blade but it’ll do

-
@Echotech said:
Thanks nakken, that was made for me by a guy in Ukraine about 10 years ago.....Russia & Ukraine have a lot of nixie tubes from old submarines and the like
That makes it even more interesting, given the current circumstances :o
Only 10 more days to go, great pictures and carries so far everyone

-
Day 20 of 30
Today used blade to open package
[attach id=0 msg=2585271]

-
Day 19
Completely forgot to post yesterday. The plain edged TF377 crew helped open some snacks. This has been my most carried knife of the challenge, and the reason is because it is the most useful. I might even say that it has an edge over my serrated, first generation TF377P, for general purpose use. I know, I know. I do apologize for that.

-
Day 20
It is a rare challenge day that allows me to carry a fixie, but today I needed the first-generation, Myerchin Offshore System B100 to open a large envelope.

-
Day 19
The WM rigging knife was on package detail yesterday. Amazon orders for the house.
Got the PowerLock all back together after the deep clean and refurb. Ended up raiding the parts bin for a bottle opener and handle covers. All the original tools are the originals. I still need the wire that goes on the 1/4” driver that holds the socket on. I know I have one around here somewhere, just can’t find it at the moment. Only thing I have left to do is sharpen the blade and adjust the pivot tension.
I had thought I had taken a picture last night and posted. When I logged in this morning, I guess I didn’t. August is going by so fast.
JonesE
-
Last night, I began tightening up the last knot on my lanyard, and actually used the spike on the SOG rigger, to get it tight.
[attach id=0 msg=2585278]
Today, I'll sit back and rest on my laurels,
[attach id=1 msg=2585278]
Total cost of my lanyard was about $3.00. (95 paracord was $2.99 and the bíner was one I had laying around).
A bit of advice to anyone that may try one out.
1 - I always have some twist ties, from bread bags, to temporarily hold the cord where I want it
.2 - pre shrink everything except for the Star knot. Shrinking the star after you're done will tighten it up nicely, but íf you don't pre shrink everything else it can come out uneven when it gets wet.On a side note, I found a cheap Chinese rigger that looks like a miniature (only 3.5 inch) copy of a WW I clasp knife. I'm not expecting much, but it was less than $10.00. may be in before the end of the challenge. If not, it'll give my Barlow something to do that day.


-
PC, your lanyard looks incredible. You did a fabulous job on it.

JonesE
-

That lanyard looks so incredibly amazing that I might have to attempt one myself, even though it looks rather intimidating as well.

-
Just take it one step at a time, guys.
I appreciate the positive replies, too. I can only hope that I did good by Bryon Toss...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

