Rebar Owner's Club (pic heavy)
-
@ThundahBeagle said:
Picked mine up September if 2017 and never looked back. Through the generosity of a member here, I got a wonderful, thick American Bench Craft leather sheath for it, and that thing is tough enough to hold the Rebar, which itself is tough. I have PST, PST2, OG Surge, Squirt P4, and other stuff but this Rebar has been a constant. When I deviated, I gravitated back to it.To my knowledge there has not been a "gen 2" and I think it does not need one. Rolled edges so it doesn't bite the palms as much, great tool load, replaceable wire cutters, locking tools, for gold school polished stainless finish...awl of it...If it had a scissors like the PST, OG Wave or even OG Surge, it would be perfect. There, I said it.
I snapped the tip of the big flathead off YEARS ago, and haven't sent it in because I didn't want to be without it. It's seen nuts, bolts, screws, very cold temperature, water, battery acid, paint, taken a few drops, and been in-sheath on my belt as I crawled under the truck or the wife's SUV for oil changes, been involved in spark plug changes, air cleaner changes and definitely hose and hose clamp work. I think it is one of Leatherman's best all-around tools ever
I have added scissors to mine, pretty simple mod and doesn't take that much work. Definitely worth it!
-
[attach id=0 msg=2592246]

-
I had a little boo-boo today, and managed to snap the small screwdriver on my Rebar. I really haven't had the best luck with my Leathermans this year.

-
Bad luck stuntzombie, luckily warranty will cover that one
-
I’ve also had issues with Leatherman small screwdrivers snapping or breaking, but Leatherman’s warranty is good.
For comparison, the small screwdriver on my SwissTool Spirit just bends after a significant amount of force, whereas the Leatherman’s will definitely snap.
However, claiming Victorinox’s warranty isn’t as easy.
The last time, they wanted to send the SwissTool Spirit to Switzerland and wait about two months for the repair.
If the repair wasn’t covered by the warranty, they offered to send my broken tool back to me or have me pay for the repair.
-
I'm actually getting ready to go on vacation, so it'll be the perfect time to send it off. Hopefully it won't take too long to repair.
It's funny, because I was using it for what I consider harder prying jobs a few days earlier, but I guess I just hit the wrong angle this time.
-
[attach id=0 msg=2592461]

-
@stuntzombie said:
I had a little boo-boo today, and managed to snap the small screwdriver on my Rebar. I really haven't had the best luck with my Leathermans this year.
Sorry man that stinks.
I broke just the tip off my Rebar 's large flathead YEARS ago. Never did send it in. Don't want to be without it and it still kinda works. I suppose I could rely on my OG Surge while the Rebar goes back and forth. I just... haven't...
-
@Vadim said:
I’ve also had issues with Leatherman small screwdrivers snapping or breaking, but Leatherman’s warranty is good.For comparison, the small screwdriver on my SwissTool Spirit just bends after a significant amount of force, whereas the Leatherman’s will definitely snap.
However, claiming Victorinox’s warranty isn’t as easy.
The last time, they wanted to send the SwissTool Spirit to Switzerland and wait about two months for the repair.
If the repair wasn’t covered by the warranty, they offered to send my broken tool back to me or have me pay for the repair.
For my part, I've never had one snap or break unless I was ** ahem ** over-using it...but these are so good it's easy to feel like they are always capable of more
-
@ThundahBeagle said:
For my part, I've never had one snap or break unless I was ** ahem ** over-using it...but these are so good it's easy to feel like they are always capable of moreI'm not blaming Victorinox's warranty; it just works differently from Leatherman's.
It was entirely my fault.
The small flathead screwdriver was simply bent, but the tip of the Phillips screwdriver cracked after a significant amount of force was applied.
-
I doubt any tool with a Phillips screwdriver would survive in that situation.
But what I am sure of is that no Leatherman flathead screwdriver would survive that amount of force, from my personal experience.
And the flathead screwdriver on the SwissTool Spirit just bent.
-
Hi! Can I join the club?
-1.jpg)
-
@Aku Harimau said:
Hi! Can I join the club?Welcome to the club! What a lovely Rebar 👌
-
Thanks, magentus, LoopCutter!
In this photo, under the diffused light of a cloudy sky, he looks uncamouflaged, like a BO.-1.jpg)
-
Haven't posted a Rebar pic for a while because of the Alox challenge, but here she is, posing with a present from my partner, back from her stay in Poland

-
Rebar with my SI at work today

-
Replacing a door panel, using the Rebar to pull nails out of the quadrant

-
[attach id=0 msg=2593133]

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
