Leatherman Flattened Bit Extender
-
Isn't that the same as the regular LM Bit Extender?
-
@max6166 said:
Isn't that the same as the regular LM Bit Extender?From what I understand, it doesn't fit the flattened bits well. I might be wrong.
-
The Leatherman extender does work with the flattened bits. They are a tad wobbly in it, but do work okay. The flat extender you drew would take up less space though :) (thanks for the Sketchup tip ari, I plan on checking that out some more) :)
-
My bit extender works well, no problem

-
I have a leatherman bit extender. It works well with the flat bits. Mine actually holds the flat bits very tight. I store it along the bit kit in the pouch, fits perfect.
-
@jetscream said:
I have a leatherman bit extender. It works well with the flat bits. Mine actually holds the flat bits very tight. I store it along the bit kit in the pouch, fits perfect.I guess I'll have to get my hands on one.
-
I think it is still a good idea though.
For one, it is much slimmer. And though the LM version works fine for some, a few others have complained that the flat bits wobble a little.
It would complicate things, but is that little spring that comes down in the center notch of the LM bits necessary to hold them in place?
-
I think that this is a nice idea.
From my experience, the lack of reach is most common wiht the smaller bit sizes though. With those, the base of the bits is the limiting factor. That flat bit extender wont adress this problem... -
So who has the metal tools to make one of these?
-
toothrot made one for me. it takes only regular 1/4" bits which is nice because they are like a dime a dozen. mine lives in the back pocket of the sheath. works great for me
-
-
-
So who has the metal tools to make one of these?
Everything on your design would be pretty easy to make ari, except for the flattened hexagon hole. :(
Would it be easier to produce in two pieces and then attach them together? Like this:
That would indeed be the way to do it. Unfortunately though, a wire EDM machine would be needed for the hole, and they aren't common. :-\
I'll send off a PM to member DoughDTD and see what he can do. :)
-
So who has the metal tools to make one of these?
Everything on your design would be pretty easy to make ari, except for the flattened hexagon hole. :(
Would it be easier to produce in two pieces and then attach them together? Like this:
That would indeed be the way to do it. Unfortunately though, a wire EDM machine would be needed for the hole, and they aren't common. :-\
I'll send off a PM to member DoughDTD and see what he can do. :)
Sounds good. What metal would be best for this? Tool steel like the bits? Also would springs or notches or magnets be needed to keep the bits in? My Wave is still being fixed, so I don't know how Leatherman keeps the bits in place. On my 1/4" drive extender I used as a model, a magnet holds the bits in.
@J-sews said:
thanks for the Sketchup tip ari, I plan on checking that out some moreI use Sketchup a lot because it is easy and free. It's a great piece of software if you don't need the power of an expensive CAD program. I'm learning VectorWorks in school for theater, but I'm not as fast as I am in Sketchup. The model took like 20 minutes.
-
Just go the simple route and make some long bits. I'd be in for a couple.
Quick PhotoChop

-
I agree. Long bits would be tons simpler and cheaper to make. My brother has a wire EDM business. The wire cutting would cost about $75 per piece...maybe more. That doesn't include machining, drilling, hardening and grinding the steel before hand. There are other issues here that make this method unrealistic.
Yeah... Long bits...Long flat bits. Not easy to make but doable I think.
Dave
-
@max6166 said:
It would complicate things, but is that little spring that comes down in the center notch of the LM bits necessary to hold them in place?I have been looking into this problem for QUITE a while actually and would love to throw my input that I've gathered so far. First of all, i absolutely love the flattened bits. I know 1/4" regualar bits are a dime a dozen, but so are decent quality pliers. However, we all carry 50+ dollar pliers on our hips for a reason....versitility. Thats why I love the flattened bits, even though they are a bit more expensive. I have no problem buying a couple sets and replacing a bit if its gets lost or damaged. I have lost a few, and despite working them very very hard, have yet to catastophicly damage any. Either way, I think the small space and weight of the set make them invaluable. Now heres the rub. I want to be able to use them effectively WITHOUT a leatherman tool or the bit driver that goes onto the phillips head. I have been trying to figure out the best way to be able to use them with the spirit driver or a 1/4" driver on the SOG driver. The problem is, the flattened bits are twice as long as a standard bit. Also they dont have a flat end like a typical bit. This creates problems when looking for a means to drive them or hold them in place. Most bit holders with a spring, similiar to the leatherman bit extender, are too shallow to grab onto the flattened bits and they will just slide out. Bit holders with a flat bottom magnet dont work because they are trying to gra onto the buisness end of the opposite driver. Here is a list of my possible solutions so far.
I wanted to try and do something very similar to what you were saying, but opposite. I wanted a full 1/4" hex bit shank on one end, and a flattened end to accept the flat bits. The regular leatherman driver extender accepts bits OK, they do wobble a little bit but work well. The slimness of your new design wouldn't help with use because it would have to rotate and take up the same effective space as the current extender. However, I do agree a flat hex hold would hold the bits more secure. Your design can be accomplished with a wire EDM if you wanted to pass it through lengthways, but I wouldnt suggest that. Take a look at the current leatherman bit driver, and you will see it gets smaller to prevent the bit from sliding all the way through. Trust me its a bitch to get the retaining ring and spring in there, I've been throwing around ideas for that for quite a while now as well. Do get a design like that you would need to CNC cut it with a very small endmill. You will actually see small circles at the corners of almost every single hex bit opening, that is from the diameter of the cutter. It would not take a terrilbly long time, but unless its a LARGE run, itll cost you more than 5 bucks. You would need to buy the steel, cut it, finish it, and heat treat it. A standard tool steel would work just fine, like an A2 or D2.
Here is something I am VERY much considering doing that could solve alot of these problems. Take the double ended hex bits from leatherman and cut them in half down the middle. Then get a regular magnetic 1/4" hex bit extender. The flattened bits would fit very securely into the full 1/4" hex adapter if there were a flat bottom for the magnet to grab onto. Then, if you need the other end of the extender flattened, just take it to a grinding wheel. It would be much much cheaper, and easier, and I think would accomplish the same thing. This is actually the route I'm going to be taking.
Let me know if you guys need any more specific information on this subjet

-Dough
-
If the result is just making a flat bit fit snug in an extender maybe you could slip some kind of U shaped spring/spacer combo down into a regular extender that has a deeper socket (if they exist) to make it fit snugly...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




