(Not) My Design for a Multitool
-
Thanks, guys.
Yes, my wife's dad is still alive. He's declining too, but he should have a few years left we can fish & tell tall tales over a beer.
I've lost quite a few folks who I was close to over the last few years, so I'm not as sad as I might be at losing my wife's mother. I buried my own father just a year & a half ago. This is all just part of life I suppose. As a performer I have to push it down so that I can smile & give my all on stage. I find time to grieve though - we all do in our own way.
Tom
-
I'm still working on my cardboard model of this tool. This summer has been tremendously busy - been working 7 days a week since Memorial Day.
Tom
-
I'm ready to get back to this now. I'm sorry if I've been leading folks on a bit. I need to find a good machine shop to do the work for me. I'm still afraid it will be a monster & very unuseable, but it's worth a shot.
Tom
-
Yay!!

-
@Tom Munch said:
Now how to add wire cutters into that jaw - either deep in the jaw or on the back somehow like I've seen on other tools.Any ideas, guys?
Tom
Hi Tom,
I saw some wire cutters that work in a similar manner to the wire strippers. I'll try to explain it here. Let me know if it isn't clear.
- open up the jaw about 5-10 degrees.
- (with a carbide drill bit) drill a hole at angle into the jaws (away from the pivot point/rivet). The hole must be drilled tangent to the travel of the jaws. (this is getting to hard to explain).
- anyway, if you then stick a wire in that same hole and close the jaws, it should cut the wire.
If you drilled a hole straight through, that would work, but and angled hole acts as a wire stripper also.
Does that make sense?
??? -
trickknife,
I've read your description several times, but I'm still not picturing what you're describing. Do you mind sketching it a bit?
Tom
-
Here's an attempt at drawing in 3D.
In "cutter 2" the jaw is pivoted so that the jaws will be closed (disregard the sloped hole for a second).
You open up the jaws slightly (about 5 or 10 degrees) and then drill a hole at an angle as shown in the image "cutter 1".
To use the wire cutter, you open the jaws up to this position (where you can see through the two holes) and insert your wire.
Then you close the jaws and squeeze on the handles. It should go back to the position in "cutter 2" and the wire should sheer off.
Is that better?
Rick


-
trickknife,
That's a good idea, but I don't know if either of the Knipex heads I'm looking at have sufficient overlapping material to do this.
-
Maybe a wirecutter could be implemented into the back where the tools scissors a bit.
Tom
-
A carbide insert could even be fastened into the jaws somehow I think.
Tom
-
-
Is that do-able, Bob?
-
Two questions occur to me about adding wire cutters to these tools:
- Location of the cutters?
- Pivot tightness?
Of the two, the Pivot Tightness question may be the real hang-up. For bypass wire cutters to work properly (and not let the wire squish in between the cutting surfaces) there needs to be very little slop between the plier jaws.
I've never handled one of these Knipex tools before. They look like the design requires a certain amount of looseness between the jaws, and between the two handles.

-
That's a good point, Bob, but they are actually pretty accurate because of the locking design of the adjustable slider. That said, it still may be very difficult to get the precision necessary to have two blades meet precisely enough to cut well. The best we can hope for may be just the ability to cut solid wire & not stranded wire.
Tom
-
Re-reading your post I agree that there is too much slop for a bypass-type cutter. I suppose there is too much slop for a two-blade diagonal-type cutter then. I wonder if a single blade coming in contact with a flat surface (I've forgotten the designation for this) would work.
Tom
-
Oh yeah...it's Anvil.
-
Yes, I was wondering about the anvil type myself.
-
So I haven't returned to this design in quite some time. Part of that is because I don't mind carrying a couple of specialized tools in my bag, & part of that is because I've been taking care of surgery-recovering relatives this Fall. I promise I won't let it go completely though. Stay tuned.
Tom
-
We understand...great minds can't be rushed :)
-
Great minds - ha! No one's ever said that about me before.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login