Flash light Jargonese.
-
@ringzero said:
LUMEN output is useful because it is a measure of the total light pumped out by the torch.LUX measurement is useful because it is the intensity of the brightest part of the torch's beam. LUX measurement can be used to predict how far the torch will throw a useful beam.
Yep, that's pretty much it. Another way to put it:
"The difference between the lux and the lumen is that the lux takes into account the area over which the luminous flux is spread. A flux of 1,000 lumens, concentrated into an area of one square metre, lights up that square metre with an illuminance of 1,000 lux."
Lux and footcandle measure the same thing, but footcandle is basically lumens/sq. ft. and lux is lumens/sq metre.
@ringzero said:
LUMEN output is useful because it is a measure of the total light pumped out by the torch.Not always--in fact, in the case of most flashlight manufacturers, they specify the lumen output of the emitter (LED) itself rather than the lumen output of the torch. There will always be a lumen loss due to the inefficiencies of the reflector and lens (window). Therefore, it makes it difficult to compare the lumen specs from one manufacturer to another. Measuring true torch lumens requires an integrating sphere, which is an expensive piece of equipment, so many times the manufacturer simply states the lumens spec of the emitter at whatever current it is being driven. Typically only the high-end manufacturers such as Surefire state torch lumens or "lumens out the front" (OTF).
-
That's a good article. Wikipedia also has some good info about flux (lumens) and lux.
-
Mike I could put together a list but specifically what are you confused about?
:Dto start and not to be too technical ;)
Lumen= usually a measure of light output
Lux....= measure of light intensity
Regulator = a circuit that takes energy from a battery and converts it to a (usually) constant current or voltage to feed the flashlight's LED,normally the output will stay constant throughout the life of the battery but will drop off significantly when the battery can no longer supply the required energy.
DD= direct drive Non-regulated light output usually in these flashlights the light will start at maximum ouput and diminishes slowly throughout the life of the battery.
Forward clicky tailcap switch= A switch that has a momentary on before a further push latches on for constant on.
Reverse clicky switch= simply put normally there's no momentary on it's just click for on and click again for off.
UI= user interface
SMO reflector= basically a smooth mirror finish mainly used for throw
LOP= light orange peel, in texture give good balance of both throw and spill apparently.
OP= normally the heavier orange peel texture used for ironing out cree rings and usually gives good side spill of light.
LE(light engine) or pill= usually meaning the circuit and LED are housed in a brass/copper slug/can and can be screwed either into the reflector/head itself or screwed into the battery pack/housing,mostly tho they will screw into the head.
-
That's a start!

-
Some jargon that comes to mind right away for me.
User Interface- The way you turn the light on and off. On multimode lights the UI can be very important. It's no good having tons of levels if it's a pain to switch between them.
Foward Clicky- A click on UI where the light can be activated by slightly pressing the button but not clicking it all the way. Forward clickies allow for momentary activation. Tactical lights generally have a forward clicky.
Reverse Clicky- A click on UI where the light is activated by pressing the button and clicking it on. Reverse clickies do not allow for momentary activation.
Reflector- Used to reflect the light froward. There are different types textured reflectors commonly smooth and orange peel or OP. Smooth ones will give you more throw but with a more ringy beam. OP will take some of the throw away but give you a smoother cleaner beam.
Optic- Some lights don't use reflectors to project the beam forward but use shaped glass or plastic. Optics can be used to focus the beam for more throw or spread the beam out for more flood. Surefire uses a optic they call TIR or Total Internal Reflection on allot of there e-series lights for throw. Here is a pic of one outside of the light.

Throw- Used to describe how far the beam of the light protects. Some lights are very throw orientated. An example of a throwy beam a Surefire E2DL:

Flood- Used to describe how much surrounding area the beam covers. The first generation Surefire L4 is very well known for having a floody beam:

Diffuser- A device that can be put on the light to diffuse of change the pattern of the beam. An example would be the Surefire F04.


-
Superb work John and James

-
Damn John beat me while I was typing. Oh well. :D What he said too. ::)
-
Good stuff fellas!

-
Hi guys here's a great resource on everything about batteries should you ever have a qeustion

http://www.batteryuniversity.com/index.htm -
@John said:
Hi guys here's a great resource on everything about batteries should you ever have a qeustion
http://www.batteryuniversity.com/index.htmThanks for the link

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login