Skeletool loose bit holder
-
Not to worry about the locking one hander I have clipped to my pocket
Having built the bugger apart, does it seem like there is room for more models/variations using the same chassis? (Probably not as modular as a Juice, but could they make some more designs using the same equipment)
I hope so , if they could somehow fit scissors in there then I think they would be onto a sure winner .
Dunc
-
Nomad what are steel caps? ???
A few hours ago I unscrewed the bolt and bent the metal retaining strip, and the bit sits a lot more firlmy in it's compartment now

-
Nice simple solution Dunc--bravo!

I don't have a Skeletool yet, but I'll sure keep this in mind when I do.
-
Nice mod! Something I didn't need because mine is tight as a drum. Where did you get that bit kit? Did it come with all those? That's awesome!
-Kit
-
The Skeletool didn't come with all those bits , I bought them seperate for £5 . They are made by a cheap tool company called Blackspur . Cheap but they seem fine to me .
Dunc
-
UPDATE
I bought another Skeletool about a month ago and I've noticed a difference which would explain the loose bit holder on my First Skeletool .
My first Skeletool was an early one so I don't know if they introduced an improvement or it just missed a sequence in its production .On the newer model the little metal lip on the frame has been slightly bent inwards to hold the spare bit snug . Heres the photos ......
New model

Another pic

and the original model

This explains why the spare bit was loose on my first model .
Dunc
-
Hi Dunc,
It is a pity that there are no date codes on the Skeletools.
I have two of the older ones with the almost straight bit retainer, Info on these is as follows:
Skeletool - Plain edge blade - 420HC - Purchased 2/08
Skeletool CX - Combination edge blade - 154 CM - Purchased 3/08My two recent purchases have the pronounced turned-down retainer lip. Info on these is as follows:
Skeletool - Combination edge blade - 420HC - Purchased 9/09
Skeletool CX - Plain edge blade - 154 CM - Purchased 9/09Hope this is of interest - Joe
-
Thats a big help Joe , thanks
It prooves that mine wasn't just a quality control issue but it was a fault that LM later rectified .This should get all Skeletool owners reaching for their tools to see what model they got >:D
I agree it is a pain there is no date codes .Dunc
-
Mine is a Skeletool CX straight blade purchased in October. It has the turned down retainer clip and is so tight as to be a little difficult to remove the bit sometimes.
-
@Dunc said:
Thats a big help Joe , thanks
It prooves that mine wasn't just a quality control issue but it was a fault that LM later rectified .This should get all Skeletool owners reaching for their tools to see what model they got >:DDunc
Well, it certainly did! I got both mine very soon after they were released, and it came as no surprise to see they were like your older one.
Having said that, even after plenty of use, the bits still fit snugly in both of mine. Looking back at my earlier post on this thread, it looks as though the scenario was common enough to make a design change. Cool.
-
Thats a big help Joe , thanks
It prooves that mine wasn't just a quality control issue but it was a fault that LM later rectified .This should get all Skeletool owners reaching for their tools to see what model they got >:DDunc
Well, it certainly did! I got both mine very soon after they were released, and it came as no surprise to see they were like your older one.
Having said that, even after plenty of use, the bits still fit snugly in both of mine. Looking back at my earlier post on this thread, it looks as though the scenario was common enough to make a design change. Cool.
Its such a shame that because of the lack of a date stamp we can't work out what year the changes took place :( Unless we email LM .
-
ANOTHER UPDATE
I have just aquired a NIB 2007 Skeletool . I know its 2007 because it says so on the box and its the original box to .
Anyway the bit holder is the later type with the metal lip bent in to retain the spare bit . So the change was made very early on then and there can't be many Skeletools with original straight/loose bit holder .Another thing I noticed is on my well used Skeletool the blade has just about worn away the little stud near the padlock symbol on the lock bar . It will be interesting to see if my latest one does the same ?
-
The Skeletool and Skeletool CX that I got shortly after they were released both have the flat retainer. The red Skeletool from REI this summer has the bent retainer.
Great spot Duncanheimer!

-
Bob are any of yours users? if so hows the blade retaining bump holding up on the lock bar .
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login