What Did You Use Your Multitool For Today?
-
Thanks Blackbeard. I should have been more clear. I used the sharp tip of the pry tool to slice the tape that was securing the box. There were no staples. I appreciate the tip.
-
I know I have been missing for a while, but I am still here in spirit! Been working the SURGE hard these days, repaired and winterized my boat motor, fixed several fences at my buddies farm, installed some cabinetry, replaced a door... and then the normal odd jobs and cutting tasks.

Thinking about posting a full length review of my time with the Surge, what I like/dislike, you know. Not sure about it though...

-
@Shane769 said:
I know I have been missing for a while, but I am still here in spirit! Been working the SURGE hard these days, repaired and winterized my boat motor, fixed several fences at my buddies farm, installed some cabinetry, replaced a door... and then the normal odd jobs and cutting tasks.
Thinking about posting a full length review of my time with the Surge, what I like/dislike, you know. Not sure about it though...

Nice to hear from you Shane and I for one would happily read your review. :)
-
Haha. Well I'm looking forward to this unbiased, impartial review :D
-
Putting my ST300 through it's paces, loving it so far.
First I used the saw to take down about a dozen branches, some about 1.5" thick. Ate through them with no flex in the saw and a solid lockup. The bigness and heft of the tool worked great with gloves while sawing.
Secondly I used the Phillips to unscrew the filter inside my dryer.
-
Finally got to use my alox electrician plus 2day on some wiring for uv lights I was installing. sheepfoot blade was quite handy & sharp.
-
I used the AWL on my Farmer to drill a hole. I needed to make a makeshift clothesline and was putting in an eyehook. I haven't handled every multi-tool but among the ones I have handled the Alox line gets the nod for, IMHO of course, best all around AWL. I also used the can opener on a can of Campbell's chicken noodle soup. The small cans have the ring that you can use to pop off the lid but the big cans still need a can opener.
-
Used Micra to tighten up a bolt on a read-a-board pole.
-
Supertool 300 snipped the excess off a few zip ties today and the can opener opened up a big can of pineapple juice.
-
Little bit of Ikea flatpackery with the KF4 ;)
-
my spirit helped me putting a E1 crossover cable together, some pics:



very helpful indeed :)

and also the chisel blade was very useful to cut myself (6th time with the same MT :o it either loves me or hates me, very much :'( )

-
Great pics there mate!
I used the screwdriver on my K502x to take mirror off a wall and then put it back up again. I didn't have to, I just wanted to :D
-
The lid switch on my washing machine went out recently. Actually I didn't know that, I just knew SOMETHING was wrong with it. Well yesterday my wife got to looking and figured it out. In my defense she told me to leave it alone as it's actually her Mom's washing machine and if she messed it up her Mom wouldn't be as mad at her as she would be at me. But anyway, this morning we went to work trying to fix it. Used various screwdrivers and also used my ratcheting screwdriver. The MT that got used was my Swisstool. I used it to unscrew some screws and the awl to pop some clips out.
We got it taken apart and got a new lid switch but we didn't get it put back together yet, that's tomorrow. So I'm assuming some of my MT's will be used tomorrow.
-
I used the awl on my ST300 to drill a pilot hole for a screw in hook.
-
Started putting up outside Christmas stuff this afternoon while the weather is still halfway nice out,use my old Supertool,used the knife,phillips screwdriver,wire cutter&pliers,and the awl,still one of my favorite tools.
& 
-
Used the saw on the ST300 to trim off some branches that were in the way. Used the PE blade as a striker on a ferro rod practicing fire making. Also used the awl on the kf4 to make vent holes in a lid. I`ve reshaped the awl on the kf4 and its now nice and pointy.
-
Charge! used to run 3 new lines of power recepticles. Stripping wire, wiring recepticles and attaching gang boxes to studs. 7 new boxes wired 4 old boxes removed.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
