Wire Cutters
-
Carbides tend to be very tough but brittle materials, i guess that's why they made them triangular so that you had at least 6 free repairs before you had to replace them. SS is softer but much more ductile which is why you tend to deform the cutters on tools rather than chip them.
-
@DavidBinGA said:
Carbide ones I had on my 800 were good, but prone to chipping. Some how SS seems stronger ???David
I think it's because SS will roll rather than chip.
-
@Roadie said:
Carbides tend to be very tough but brittle materials, i guess that's why they made them triangular so that you had at least 6 free repairs before you had to replace them. SS is softer but much more ductile which is why you tend to deform the cutters on tools rather than chip them.::) should have read your reply before answering dave's :D
-
Since you all are on the subject (kinda), I've been wondering if those Gerber cutters work on thick material. Seems to me that the design would get caught up on anything thick (like heavy gauge wire for example)?
-
Well I haven't got a set to test (yet ::)) but i would imagine that would be the case :)
-
Well i just compared the cutters to the swisstool using a coat hanger as the material and the Gerber took a lot of effort to cut it but managed it, the swisstool went through it a lot easier but neither were uncomfortable to use!
-
Thanks for the test :) I was especially wondering about thick soft wire like maybe #4 AWG solid copper, but I doubt anybody has any of that just lying around ::) and I haven't really tried it with any MT, so maybe 10,8 or 6 would be a better quesiton.
-
Don't think i have any solid core wire hanging around but i'll have a look, not something i've needed much at uni! But should i come across some i'll be certain to give it a shot.
-
Yeah, it's not an everyday thing at all unless you're doing electrical work... Thanks for the help though

-
The carbide cutters on my Gerber can't cut stranded wire...it just bends between the cutters. I've got them tightened beyond tight, but I guess the design just leaves a tiny space where the stranded wire get's hung up.
Any heavy gauge or otherwise solid stuff is fine though.
I'd also agree with David...SOG cuts everything effortlessly and cleanly

-
Got that right Corrugated, SOG kicks butt. I do have to say, SOG has brute force, but new leathermans can cut paper like scissors...for precise work, Leatherman is your tool.
David
-
Yes, but how many "precise" cuts have you made on wire? ;) I can easily strip fine wire with my Powerlock.
While we're on the subject; my Crunch arrived today and I stripped a wire on my first try with that odd integrated wire stripper. It's a little odd but it works!
-
I think that the cutters on SOG's new pliers are even better than the original. The cutter is wider and has a much better edge. In my opinion, the best cutters are on the new SOG and the Paladin PT-525. The Gerber Diesel has a pretty good cutter also. I was able to cut lamp cord with all three (also the Leatherman E4...though the small cutter required a couple of passes). Every other multi-tool that I've tried makes a mess of finely stranded wire. (Although it's a fine tool in other respects, the SwissTool spirit was the worst on lamp cord. The fine wires got mashed between the jaws and I had to pry the jaws apart. The Leatherman Crunch was 2nd worst on stranded wire. The Charge and SwissTool were about equally poor--they cut some but not all of the wires on one pass. I haven't tried the stranded wire cutter on the Leatherman Core & Surge) The new SOG cutters also handle solid wire (10 gauge) well but I haven't tried cutting a fence with them. Although I don't cut a lot of lamp cord, I cut lamp cord more often than fencing. I still go to my trusty Klein pliers when I'm planning a project requiring heavy cutting.

Here's a photo showing the SwissTool Spirit jammed on lamp cord (right panel). I can actually suspend the SwissTool Spirit by the wire. It didn't take a lot of force but I did have to pry the jaws apart. It had just mashed the wires rather than cutting them (left panel). The clean ends were cut with the new SOG.

-
@supratentorial said:
I think that the cutters on SOG's new pliers are even better than the original. The cutter is wider and has a much better edge. In my opinion, the best cutters are on the new SOG and the Paladin PT-525. The Gerber Diesel has a pretty good cutter also. I was able to cut lamp cord with all three (also the Leatherman E4...though the small cutter required a couple of passes). Every other multi-tool that I've tried makes a mess of finely stranded wire. (Although it's a fine tool in other respects, the SwissTool spirit was the worst on lamp cord. The fine wires got mashed between the jaws and I had to pry the jaws apart. The Leatherman Crunch was 2nd worst on stranded wire. The Charge and SwissTool were about equally poor--they cut some but not all of the wires on one pass. I haven't tried the stranded wire cutter on the Leatherman Core & Surge) The new SOG cutters also handle solid wire (10 gauge) well but I haven't tried cutting a fence with them. Although I don't cut a lot of lamp cord, I cut lamp cord more often than fencing. I still go to my trusty Klein pliers when I'm planning a project requiring heavy cutting.
Here's a photo showing the SwissTool Spirit jammed on lamp cord (right panel). I can actually suspend the SwissTool Spirit by the wire. It didn't take a lot of force but I did have to pry the jaws apart. It had just mashed the wires rather than cutting them (left panel). The clean ends were cut with the new SOG.

Great test results you've got there.
You hear a lot about those Klein pliers. What are they exactly?
-

Klein (http://www.kleintools.com/) makes a number of different pliers. The side cutting pliers in the photo is one of my favorites for heavy duty work. Here are some specs:
* 2000 series cuts ACSR, screws, nails and most hardened wire. * High-leverage design. Rivet is closer to the cutting edge for 46% greater cutting and gripping power than other plier designs. * Streamlined design with sure-gripping, cross-hatched knurled jaws. * Induction-hardened cutting knives for long life. * Hot-riveted joint ensures smooth action and no handle wobble. * Features combination polished and black-oxide finish.Knipex (http://www.knipex.com/) also makes a very good pliers.
-
Wow, I like those nice clean cuts by the SOG in the mashed wire picture :)
I'm a fan of the Kleins as well. They can cut just about anything you have the strength to cut, and without taking any damage. Of course if you want to get real tough one of their ratcheting cutters would be pretty neat to have, but they're a little too much $$$ for me... :(

-
Bloody hell they look like a tool and a half :o
-
They sure are :D They're fun to use too... One thing though is that their made more for copper and aluminum, so if you try to use it on anything too hard you can nick it up :( The regular kleins you don't have to worry about that thoug :)
-
Yeah they look awesome!
Would have loved some of them in my last job. I always used Maun cutters there.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login