Charge TTi Issue
-
Hi,
I have recently purchased a new charge tti and I have a couple of questions I'm hoping some of the people around here can help me with. The first charge I received in the mail had an assembly problem. On the piece of the tool where the lanyard and pocket clip connect there was an extra washer and spacer in place, this pushed the titanium handle out and stopped it from mounting flush with the ruler piece (hope this description makes sense!).
I contacted the supplier and had a new unit shipped out asap. This new one was a lot better except for the fact that the file rubs against the titanium side handle piece. I realize this probably wont cause too many problems but it is a bit concerning, especially given the price of this tool. My question is, is this a common problem? Is this grounds for another RMA and replacement to be sent?
Thanks for your help!
-
I had a TTi(I say had cuz I traded it) and I think my file rubbed ever-so-slightly against the handle. it was very light rubbing, I didn't think it was anything to worry about. If it is really grinding and doesn't go in all the way then its definitely a problem. I am not sure if this is an ongoing problem or just a couple of 'em. If it bothers you, definitely put that 25yr warrantee to good use

oh and welcome home

-
There have been a few people complaining about the file rubbing on Charges lately, and it really shouldn't - as you say it's an expensive tool and the fit should reflect that (IMO anyway).
I'd say that if you aren't happy with it, return it for one that you are happy with - I certainly would :)
-
The file?
Constant
Handle
Abuse by
Rubbing and
Grinding
Every time -
Haha nice one Charger! I have contacted the supplier and will see what they say. Hopefully I can get another one shipped out. I agree its only minor but I know it is going to bug me later on so may as well try get a good one.
Will see what happens.
Thanks.
-
Probably just need to tighten up the file pivot bolt. I think they leave them a little loose so the knife blade opens easier but that can cause rubbing of the file and saw and cause the liner lack to travel to far over also. I
ve had to adjust every Wave and Charge Ive got to find the right tension to make everything work as it should. Liner locks can be fussy and when you have four of them on one tool it can be down right frustrating. -
Welcome to the forum mate

And like Dave said, just send it back, as there shouldn't be fault's on something that expensive :)
-
welcome to the forum tack , as the guys said send it back,
or buy a wave :D

-
Are they ever gonna fix this problem? I really want a charge. THe one I returned to amazon and all these stories really put me off.
-
They aren't all like it BB - I have lots of Charges (lol I can't recall exactly how many :-[ ) and not one of them has / had this problem. I've handled many more that I've sold or traded too, and they were all good :)
I understand what causes it, as I can recreate the problem when reassembling Charges and Waves, but it's not really acceptable to expect someone who's shelled out for a Charge to be thinking about adjusting things on a new tool IMO.
-
The file on my Tti rubs so bad that I barely have any diamond left on the file.
-
You should get it repaired or replaced GB. Apart from anything else, it makes sense to let LM and their repair centres know that this problem occurs often enough to piss potential customers off :)
-
this was like mine
i would have sent it back but i couldn't be bothered with the hassle
-
@DaveK said:
They aren't all like it BB - I have lots of Charges (lol I can't recall exactly how many :-[ ) and not one of them has / had this problem. I've handled many more that I've sold or traded too, and they were all good :)I understand what causes it, as I can recreate the problem when reassembling Charges and Waves, but it's not really acceptable to expect someone who's shelled out for a Charge to be thinking about adjusting things on a new tool IMO.
Seems the charge is based on the wave blueprint...and when you slap on the thicker titanium scales, the natural bend in the file becomes more pronounced and rubs on some of them...I just dont relish the thought of buying it and sending it out for repair, wish they would just do some redesigning and be done with it. I'm sure they get more of this type of repair than anything else.
-
I don't think it's the design per se (as I say I have about 15 "good" Charges), it's more to do with the positioning and tensioning of the plier pivot screws - they need to be "just so" and it looks like they're not always getting it right.
-
well if I can win one on ebay for the right price, I might take another chance.

-
It almost seems like the file is bent or warped on mine.
-
@DaveK said:
I don't think it's the design per se (as I say I have about 15 "good" Charges), it's more to do with the positioning and tensioning of the plier pivot screws - they need to be "just so" and it looks like they're not always getting it right.Thats a lot of Charges. Is that one of your favorite MT?
-
I do have a soft spot for them, yeah ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login