First go at wooden scales,
-
That is genius! I just checked out Neils walk through, and I think I will try it on my spartan as soon as my pin stock arrives from Tom in the mail. the mod I am getting back from him has a back spring Phillips that I want to swap for a corkscrew, problem is, the knife is a four layer with a cybertool layer in it. Hints/tips would be welcome!
-
@gadgetguy35 said:
That is genius! I just checked out Neils walk through, and I think I will try it on my spartan as soon as my pin stock arrives from Tom in the mail. the mod I am getting back from him has a back spring Phillips that I want to swap for a corkscrew, problem is, the knife is a four layer with a cybertool layer in it. Hints/tips would be welcome!I have to admit the thickest SAK I've done this on was just two layers so I'm not sure how easy four layers would be. A good general tip though is to make sure that you put a long, thin taper on the rod to be tapped into place. It means that the liners and tools don't have to be absolutely perfectly lined up, just very nearly so. :D
-
That is genius! I just checked out Neils walk through, and I think I will try it on my spartan as soon as my pin stock arrives from Tom in the mail. the mod I am getting back from him has a back spring Phillips that I want to swap for a corkscrew, problem is, the knife is a four layer with a cybertool layer in it. Hints/tips would be welcome!
I have to admit the thickest SAK I've done this on was just two layers so I'm not sure how easy four layers would be. A good general tip though is to make sure that you put a long, thin taper on the rod to be tapped into place. It means that the liners and tools don't have to be absolutely perfectly lined up, just very nearly so. :D
Yea, rebuilding this one the first time drove me bonkers! I almost had it, I just over peened one of the rivets and bent it. Tom told me that the cybertool layer is the hardest to mod, so I don't feel that bad. I plan on modding a wenger can opener to fit in a Vic, I am not sure how the spring will need to look for that. I will be sure to let you know!
-
cheers gareth for the link, and thanks neil for the pm

-
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now

-
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
:ahhh i bet that was annoying Neil, ill stick with scales at the moment i think,

-
I've given in with it for the day before I do something rash with it
Its using parts I can't easily replace if I muck it up big style :ahhh -
I can't redo anything until my box of goodies gets here from rotokid. I feel ya though neil, I have had to do that, only I couldn't recover it!
-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
-
Ah yes, the old "lob it as hard as you can whilst screaming at it" jobbie. :D Almost as satisfying as the "punch it as hard as you can because you banged yourself on it" one. :D
-
@DaveK said:
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
-
I'm not allowed to throw things anymore... My wife gets angry!

I just take a step back, gooz fraba, and my left eye twitches for some reason, but I feel better!

-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
My condolences Neil, I hope she pulls through.

Sounds like the typical crap that happens to me!
-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
Ah OK, that truly sucks. :( If it's any consolation I'd have had to do something about the ugly pin as well, I can just about live with it if it's under a scale, but I couldn't be happy with it out on display. I really hope the liners are OK.

-
If it was under a scale (unless translucent) I would have left it alone as mechanically it was sound. I'd even have left it with a slight split at the circumference, it is a hand finished product after all but a chip is just bad :(
I should have bit the bullet and pulled the thing apart there and then instead of taking a shortcut. We live and learn :)
-
I hope its ok if i post that here. Made some scales from Micarta for my Wenger, handles were falling apart anyway.


Came out quite nice, although i could had done a better job, i wanted do get over with :DBest wishes
Robert -
That looks like a good job Robert.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
That is the traditional response but fortunately I don't have a garage :D