First go at wooden scales,
-
I'm not allowed to throw things anymore... My wife gets angry!

I just take a step back, gooz fraba, and my left eye twitches for some reason, but I feel better!

-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
My condolences Neil, I hope she pulls through.

Sounds like the typical crap that happens to me!
-
Although it is always followed by remorse, there are few things more satisfying (for a second at least) than wanging a non-conforming SAK at the garage door!
Usually accompanied by a ritual "chant" that rhymes with clucking bell......
:D :D
@Neil said:
Even with practise mods go wrong :( This afternoon I thought I was finishing off a four layer 93mm ..... All went well until I checked the scissors layer, no snap :ahhh I'm actually pretty annoyed as I've had to drill out the pins and pull the whole thing apart again. I know what I did wrong but that isn't making me feel any better right now
If it's not to soon, can I ask what went wrong? Far easier to learn from others mistakes I find. :)
Way too soon >:( <looks at tray of parts and seethes>
Oh, OK :)
I finished peening and didn't like the look of the head on the middle pin. The edge had chipped out, functionally fine but ugly. I don't do functional but ugly so decided to replace the pin. As you know you can do this without stripping the knife down but you have to be careful. Anyways, I wasn't careful and slightly bent the new pin going in. I'm just hoping that when I put it together again that I haven't damaged the liners. This would normally be bad but on this occasion it would be very bad as they are all brass :ahhh
Ah OK, that truly sucks. :( If it's any consolation I'd have had to do something about the ugly pin as well, I can just about live with it if it's under a scale, but I couldn't be happy with it out on display. I really hope the liners are OK.

-
If it was under a scale (unless translucent) I would have left it alone as mechanically it was sound. I'd even have left it with a slight split at the circumference, it is a hand finished product after all but a chip is just bad :(
I should have bit the bullet and pulled the thing apart there and then instead of taking a shortcut. We live and learn :)
-
I hope its ok if i post that here. Made some scales from Micarta for my Wenger, handles were falling apart anyway.


Came out quite nice, although i could had done a better job, i wanted do get over with :DBest wishes
Robert -
That looks like a good job Robert.

-
OK there varnished and im off later to get the poxy so should have some finished pics later

-
Thanks guys.
One good tip Zed. Don´t put to much glue on it, the first time i did this, i glued all my tools shut :D
I had only put some of the glue in the holes i drilled for the rivets, that should hold just fine. -
One good tip Zed. Don´t put to much glue on it, the first time i did this, i glued all my tools shut :D
I had only put some of the glue in the holes i drilled for the rivets, that should hold just fine.
yeah i did think this before i mixed the poxy up, well should have pics soon 
-
All done, ive learn a lot, but this turned out ok, now for my next project :D


-
Looking good Mate!

-
They really do look good mate.
I need to give this a go myself sometime. -
cheers guys, ive just lightly sanded the Finnish as a bit too dark for me :D but it all worked out nice plus is thinner now so fits nice in my pocket,
have a go gareth its pretty easy,paul
-
Ok some outside pics, ive now given it a light sanding to give it a more lived in look :D, its just how i wanted it,



-
Nice job that Paul

-
have you thought about getting a wood burner pen and stenciling your name on it?
:P
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login