Best Awl Design and Shape?
-
Another vote here for the awl on 93mm SAKs

-
*With the aid of all of your input and photos, I mixed and matched ideas and came up with an awl solution that I think will work great for me. I started off with metal better than that of the standard Wave blades, so it should be able to handle the abuse it will see. I went with a long, slender awl... just a hair over 2.5 inches. I noticed that the majority of awls sharpen the same edge so that it cuts when turned clockwise. In order to have clearance for the plier head, I had to sharpen the opposite edge (some SOG's are sharpened like this?). This turned out to be a blessing in disguise as I am naturally left handed. I tapered the thickness at the tip, similar to a Spirit, but not so much so that the tip would lose strength. The tip itself... I did a mild version of the beveled tip of a SOG (only 1/8 inch). There were definitely some clearance issues to deal with. If I wanted a short stubby awl, the process would of been straight forward. Since I wanted a larger, more substantial awl, I had to make a notch on one edge to get it to sit flat inside the tool. It is so long and wide that it overlapped the flat part of the scissors handle, which I will have to reshape tomorrow so there is no interference. It is a supertight fit but managed to utilize every bit of extra space in there. The large flathead driver (which I may still replace) got moved to the other handle next to the large bit driver. I wanted all things screwdriver related on the same handle. The awl is where the large flathead driver was. I am eliminating the small bit driver altogether as I will never use it because I have a complete set of double ended precision screwdrivers I made to fit the large bit driver. So... now I have the extra spot where the small bit driver was. Debating on what I will put there. Oh, also, anyone have any Surge scissors they are willing to sell or trade? Time permitting, in a day or two I will have finished and cleaned up the install. Afterwards, I will post pics. Thanks again you all!!
~ evil ~*
-
I have an old British army knife. Would be a great EDC if I could actually open the damn thing. :D
-
i gotta see pics of all your (bit)mods yet too. are they posted anywhere?
yes ALL not awl. SOmething about that word brings out the worst in peoples pun habits
-
Hey gang! It's AWL done. I apologize for the quality of the pics, they were taken with my phone.....
Initial cutting and shaping to fit into the Wave.....

It is subtle, but the thickness tapers towards the tip. Cutting edge added and sharpened.....

Close-up of bevel grind on the tip.....

Installed.....

Yet another view..... this thing is huge!

*All in all, I am quite pleased with the outcome. After dealing with the clearance issues, it folds up and locks perfectly. I put it through the paces today by punching holes and reaming just about everything in sight. It passed the test with no problems or issues. Thank you all again for your input and your photos. They helped a lot in the decision making process for making an awl that suits my needs perfectly.....
~ evil ~*
-
Wow. That thing is a pig-sticker. :o
You may have the first tactical awl there. :D
-
Great job Evil,looks real practical,are you going to patent it,or just make enough for all the members.
& 
-
That's really impressive work there mate

-
@Charger said:
i gotta see pics of all your (bit)mods yet too. are they posted anywhere?Hey Charger. They are not posted yet. They are a part of my Skeletool project. While the Skeletool is already done (for now), I still have a few more bits in mind and had planned on posting them together. One card is basically hex drivers since I am an avid bicyclist. Other bits are an awl, 6 precision screwdrivers (3 phillips, 3 flat) for all of the electronic stuff I like to tinker with. Still debating on a few other bits to make. The one I put the most time, effort and thought into so far is my flat 1/4 socket driver.
@Chako said:
Wow. That thing is a pig-sticker. :oYou may have the first tactical awl there. :D
Thanks Chako. Part of the inspiration came from the pics of those long awls you posted. As a testament to being a tactical pig sticker, it punched through a car door, if that counts >:D
@Smitty44 said:
Great job Evil,looks real practical,are you going to patent it,or just make enough for all the members.
& 
Thank you Smitty. If I had a way to mass produce them I would gladly make more of them. Keep in mind I am very old school in my ways. Any and all mods you ever see me do are done by hand tools and common everyday power tools. No fancy expensive machines here :)
-
That looks flippen impressive mate 8) 8) 8)
To paraphrase Crocodile Dundee "That's not a AWL THIS IS A AWL" :D :D
-
That is a very well finished tool you've made. Hats off to you

-
@Multitaskertools said:
I am just curious why the std awls are so short? ???I think they're only intended for thin materials (leather, thin board, sheet metal), or for starter holes for screws in thicker materials. That's also why they're tapered: perfect for starting screws, and in thinner material you can adjust the size of the hole by how far through you ream.
-
Vic's Alox awls , by far .
Chris
-
When you going to start selling them awlsome tool replacements? >:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

:D