LM bit driver
-
I'm considering attacking this problem by hacking up a set of MUT bits when they finally come out. Chop those crazy-long bits in two, and make two considerably-longer LM flat bits out of them. The only reason I'm considering cutting them in two is to reduce some mechanical advantage that might bust my Wave, and so that I could more easily thin out the shaft to be the same width as the screwdriver head, meaning they'd fit better in some recessed areas.
Entirely theoretical at this point, as I don't have the bits, and I don't know if any of my tools would cut them if I did :P
-
@SlackOne said:
I'm considering attacking this problem by hacking up a set of MUT bits when they finally come out. Chop those crazy-long bits in two, and make two considerably-longer LM flat bits out of them. The only reason I'm considering cutting them in two is to reduce some mechanical advantage that might bust my Wave, and so that I could more easily thin out the shaft to be the same width as the screwdriver head, meaning they'd fit better in some recessed areas.Entirely theoretical at this point, as I don't have the bits, and I don't know if any of my tools would cut them if I did :P
A dremel with a cutting wheel on it will cut any MT steel there is. Get the reinforced ones, they last awhile.
-
i thought the bits were a bit tougher then MT steel?
-
You will find that a grinder will cut anything depending on the disk ;)
-
-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

I love mine, don't know what I would do without it.
-
i thought the bits were a bit tougher then MT steel?
They are tool steel, and harder than the rest of the tool, but any cutting disk will go through them like butter. I just suggested dremel because it is small and you have a greater dexterity than a 3 inch cutting disk.
i find my dremel grinds pretty much everything, great little tools

I love mine, don't know what I would do without it.
for a long time i built custom diecast models and the dremel is a really handy tool for this,


-
Those are sweet, Zed! I used to build model ships, but I got out of it when my son was born. Too many small pieces around the house. I have to keep my hobbies contained to the garage.
-
@gadgetguy35 said:
Those are sweet, Zed! I used to build model ships, but I got out of it when my son was born. Too many small pieces around the house. I have to keep my hobbies contained to the garage.cheers mate , i built mainly muscle cars and movie stuff, and i built a lot of general lee's :D
here are some of the 30 year old tin plate charger i did , i loved getting these as most was in very poor shape, the end one was being stripped down at that time of this pic, the F&F charger was one of my favorite projects i did, these are very big 1:16th scale,

-
My favorite was the Cutty Sark clipper. I built two of these, but neither survived a cross country move.

-
@gadgetguy35 said:
My favorite was the Cutty Sark clipper. I built two of these, but neither survived a cross country move.
very nice mate, ive never built a boat, TBH i have no patience, the cars was taking me about 2-3 weeks to do, the rigging alone must of taken you ages :o -
I`d get the Topeak Mini Ratchet Rocket and buy some descent standard bits.
The leatherman bitholder is nice if you dont have anything alse around but the Mini ratchet is the screwdriver i use most at home.If you want a wave and dont know what to do whith the screw driver, just modify it to hold t-shank blades. That way you can add some really nice saws to your wave.
-
@Zed said:
[quote author=gadgetguy35 link=topic=19169.msg364728#msg364728 date=1271750545]
My favorite was the Cutty Sark clipper. I built two of these, but neither survived a cross country move.
very nice mate, ive never built a boat, TBH i have no patience, the cars was taking me about 2-3 weeks to do, the rigging alone must of taken you ages :oThe rigging can be quite frustrating. It can take a week by itself. It used to take me about two weeks to get all the parts trimmed, painted, and assembled. Then it took a few days to trim the sails and hang them, after that the rigging goes on. I would love to do another, but I just don't have time right now. Not much MT use on these though, all I used was an exacto knife and scissors.
-
I built a Cutty Sark when I was a teenager, it was detailed down to the crew with different color eyes and facial hair, it did not come with sails, so I made my own. My younger brother used it for BB gun practice when went in the service. Something for which I could never forgive him.
-
@valvestem125 said:
I built a Cutty Sark when I was a teenager, it was detailed down to the crew with different color eyes and facial hair, it did not come with sails, so I made my own. My younger brother used it for BB gun practice when went in the service. Something for which I could never forgive him.That sucks. I had to toss one of mine in the garbage because there was just no way to package it for our move.
-
Yep, considering it was over 40 years ago and still bothers me to this day.
-
@valvestem125 said:
Yep, considering it was over 40 years ago and still bothers me to this day.i stilll feel this way about a matchbox car i buried in my mums back garden :D

-
@gadgetguy35 said:
My favorite was the Cutty Sark clipper. I built two of these, but neither survived a cross country move.
I've been on her a few times when I was a kid :)
Damn fine model mate

-
Thanks mike! To be clear, the ship in the picture is not my model, I just built two exactly like it. The one in the picture was done by a pro with incredible detail. Mine were almost that good! ::)
I would love to see her in person after they are done restoring her. I would also love to see her sister, the City of Adelaide, restored, but it seems no amount of money can stop the inevitable scrapping.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login