WD40?
-
I think WD-40 has it's place in the ol' tool cabinet. It is more solvent than lubricant and, as it has already been stated, It's good at what it's made to do.
-
Nano-oil (thanks again Christian) for my mt, Nyogel for my torches
-
Since I use my SAKs and MT's on food sometimes, I use mineral oil.
However, I must say, I thought lard would have been brought up by now. :P
-
I have used it on my MT's for years and it works for me.
-
@Mr. Whippy said:
Since I use my SAKs and MT's on food sometimes, I use mineral oil.However, I must say, I thought lard would have been brought up by now. :P

i use it on all my tools >:D
Great with swisstools, tamales, tex-mex, PSTs, and fried chicken.
I use it as deordorant, hair gel, toilet paper and in my coffee. It's healthy too! Lubes up your heart so it pumps easier.
::)
-
Gotta keep them arteries nice and slippery
-
Bones Speed Cream. Good enough for my swiss racing bearings, good enough for my multitools.....

-
WD40 is fine. People always seem to attribute magical nasty properties to it. But the stuff is mostly a kerosene-like solvent with some mineral oil added. The solvent thins out the oil, and is relatively quick to evaporate, leaving the oil behind. It's a perfectly adequate lube for multitools. ANY oil will attract dirt. Which is why oil of all types should be used sparingly, or else it will attract dirt and other contaminants, leading to gumming and crud. WD40 isn't all that flammable. In the old days, they used butane propellant, which was great for us firebug kids. We had so much fun, they decided to switch to CO2 or something much safer. So now, the oil and solvent will burn, but nothing like the old butane propellant, or even gasoline. It tends to want a wick to ignite. Honestly, though, if you can get away from using oil at all, I find that to be the best option. MTs are not sealed mechanisms. Their oiled joints attract dirt, which may increase wear by keeping a greasy dirt slurry in all those parts that rub together. This increased wear and gunk then demands more oil be used to remedy the situation, which is only a temporary and repeating cycle. I find if a tool operates smoothly enough without lubrication, it's best to leave well enough alone.
BTW, Leatherman recommends WD40.
-
My wife told me to get some of this ............

She told me that if I put it all over my tool we would have a very enjoyablee evening :) She wasn't wrong
I got out all my multis and starting with a Spirit I lubed my entire collection finishing with a Vic Classic .I had a great time , its been ages since I got all the collection out on the kitchen table . I thought my wife was going to help but she went to bed really early 
Dunc
-
Women! ::)

-
Interesting that they ship them with something else on them!
@Dunc said:
My wife told me to get some of this ............
She told me that if I put it all over my tool we would have a very enjoyablee evening :) She wasn't wrong
I got out all my multis and starting with a Spirit I lubed my entire collection finishing with a Vic Classic .I had a great time , its been ages since I got all the collection out on the kitchen table . I thought my wife was going to help but she went to bed really early 
Dunc
:D
-
I personally wouldn't ever consider lubricating anything with WD-40. It is designed to displace water, not lubricate.
I recommend mineral oil unless the tool sticks, then I would recommend nano-oil.
-
@NutSAK said:
I personally wouldn't ever consider lubricating anything with WD-40. It is designed to displace water, not lubricate.Though commonly repeated, this is not completely true. Not only will it help disperse water, it will also lubricate. It's even advertised as such. Really, is there any reason to believe that WD40 will not lubricate? Look it up. It's just thinned oil. I suppose it won't work well in the crankcase of an old Ford. But for knives and hand tools, it works just fine.
This same nonsense goes on with bicyclists. Mention WD40 as a chain lube on bike forum, and watch about half the heads explode, claiming a whole litany of reasons it will destroy your precious bike, usually starting with the trope, "...but it's designed to displace water!". The other half will say they've used it for years and never noticed anything bad as a result.
-
@Dunc said:
My wife told me to get some of this ............
She told me that if I put it all over my tool we would have a very enjoyablee evening :) She wasn't wrong
I got out all my multis and starting with a Spirit I lubed my entire collection finishing with a Vic Classic .I had a great time , its been ages since I got all the collection out on the kitchen table . I thought my wife was going to help but she went to bed really early 
Dunc

-
Where to get food grade mineral oil?
thanks guys 
-
Hey guys, thanks for all the great feedback. Seems like there is some divide over the effectiveness of WD40 as a lubricant. Well, I'll have to invest in some nano oil and mineral oil to compliment the WD40. By the way, my wife is now convinced I am a total loser for asking you guys about lubing my MTs.
Ryan
-
I personally wouldn't ever consider lubricating anything with WD-40. It is designed to displace water, not lubricate.
Though commonly repeated, this is not completely true. Not only will it help disperse water, it will also lubricate. It's even advertised as such. Really, is there any reason to believe that WD40 will not lubricate? Look it up. It's just thinned oil. I suppose it won't work well in the crankcase of an old Ford. But for knives and hand tools, it works just fine.
This same nonsense goes on with bicyclists. Mention WD40 as a chain lube on bike forum, and watch about half the heads explode, claiming a whole litany of reasons it will destroy your precious bike, usually starting with the trope, "...but it's designed to displace water!". The other half will say they've used it for years and never noticed anything bad as a result.
Sorry, but I have to disagree with this. WD-40 does indeed have some lubricative properties - no doubt. But to suggest that it is on a par with purpose designed oils just isn't right.
I don't think anyone's suggested that it will do any harm to multitools, but it clearly isn't as effective a lubricant as say, the gun oils, nano-oil and others that have been mentioned. In fact, WD-40 actually produce "3-IN-ONE" PTFE products that often sit on the same shelf in hardware stores, and it is this that is marketed as "Ideal for chains, cables and gear mechanisms". The WD-40 can says "Stops Squeaks, Drives Out Moisture, Cleans and Protects, Loosens Rusted Parts and Frees Sticky Mechanisms".
Don't get me wrong, I use WD40 a hell of a lot for releasing seized tools, cleaning and ensuring moisture has been dealt with on tools that I restore - it's great stuff. But one of the above oils will provide efficient lubrication for longer on a multitool, which is why I switched from using WD-40.
@Rhino1227 said:
Hey guys, thanks for all the great feedback. Seems like there is some divide over the effectiveness of WD40 as a lubricant. Well, I'll have to invest in some nano oil and mineral oil to compliment the WD40. By the way, my wife is now convinced I am a total loser for asking you guys about lubing my MTs.Ryan
Ah, what do they know ;)
-
Where to get food grade mineral oil?
thanks guys 
Look in a pharmacy; they're sold as laxatives, but it's all the same. :)
A pharmacy? Hmm! I think I'll take my tool along and show them exactly what wants lubricating,I don't want them to get the wrong idea
:DYa dont lube tools with that stuff , slippery but very latex unfriendly !
Chris
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login