Case to replace Victorinox
-
I hope you get on with it Neil. The stockman is the pattern I have and feels more "special" than a SAK.
-
They do feel like quality blades and I was assured whilst in the US that "Case is king"!
-
All I've done so far is reprofile the broken tip..

.. not quite the same as the original but I didn't want to encroach on the nail nick.
Don't panic I did get permission before attacking it :D
-
That is incredible work,
WHO GAVE YOU PERMISSION? 
-
Great work Neil.. :o

-
Thanks, it looks better in the photograph but it 'll do the job nicely ;)
-
Typically fine work there mate

I'll be watching this thread with interest, as I've always gone back to a sak after a day or two at most :-\
-
SAKs will be hanging around on standby, the difference is the Case will be along for the ride.
-
That'll be something else interesting actually. Which blades get used for what.
-
Neil,
Good for you bud, nice #18 pattern stockman you got. While SAK's are all fine and good I am of the opinion for everyday cutting chores nothing beats a well made traditional slippie......and you can't go wrong with a Case.

Though be careful, slippies can be addicting.....particularly Case's and the like.
And might I add, if you every get the hankering to go up a notch with another stockman give Case's larger #75 pattern a look. One like this Silverscript piece..........

..............these'll spoil ya! ;)
2xTap
-
Great work on that blade Neil. :)
-
Good for you bud, nice #18 pattern stockman you got. While SAK's are all fine and good I am of the opinion for everyday cutting chores nothing beats a well made traditional slippie......and you can't go wrong with a Case.

Though be careful, slippies can be addicting.....particularly Case's and the like.
And might I add, if you every get the hankering to go up a notch with another stockman give Case's larger #75 pattern a look. One like this Silverscript piece..........
...
..............these'll spoil ya! ;)
2xTap
I thought you'd approve of my little experiment :D
Now quit showing me lovely looking knives that I can't afford ;)This evening the Case has been doing packaging duty.
This brings up a discussion Gareth and I had the other week, how sharp is sharp enough. For me if a blade can slice through a sheet of bubblewrap without snagging its sharp enough.
Well the newly repaired sheepsfoot blade accomplished that without issue and then went on to the slightly more arduous task of slicing up corrugated cardboard. I've got it set presently with a thirty degree bevel so it'll be interesting to see how long that holds up. I would have been better using the clip blade for the bubblewrap but it wasn't quite sharp enough, tomorrow I'll give its edge a tickle :)Thanks Ben, you'll be able to check it out in person next weekend

-
Wow!
How do you reprofile blades? I am unfamiliar with the methods. Tis brilliant!
-
I use sharpening stones. Much slower than hitting it with a Dremel but you don't have to fret about mucking up the temper and because you're working slower you're also less likely to make a mistake and muck it up :)
-
You have patience, I'd throw it on a belt sander.
-
Nice repair job as always Neil.
I've been carrying a very similar Case Stockman on and off for a couple of weeks now, while I don't think it's replaced a SAKs' special place in my heart there's no doubt it's a cracking knife. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login