Why Lanyard?
-
I personally only use lanyards to make a small item bigger(like a vic classic that gets tossed in a pocket), make them easier to extract from pockets/pouches/sheaths, and to attach them to myself if I am working anywhere high up or wet. They can make your tool less use-able like you said, but that is what the Mcgizmo clip is for! Head on over to JSBurly's on EDCforums and you will find the Mcgizmo clip. It makes your lanyard a quick release instead of a permanent fixture to your tool or knife.
-
Re: Why Lanyard?
Because it gives us another hobby, making stuff with paracord :D
-
I actually do keep a 91mm SAK on my keyring a lot of the time. I use the whole knife like a keyfob, and often just stick the knife in my pocket and let the keys hang out the side. It's also on a quick release if I need it independently. It's a little bulky at times, so depending on the pants I sometimes swap it for a Micra. But if I didn't have it on the keyring, I wouldn't carry it at all as I feel the average SAK is too slippery to just toss in a pocket.
I keep a small loop lanyard on my little bitty AA flashlight all the time. It makes it easier to retrieve from a pocket, makes it easier to find if I drop it, and when it's looped around my wrist it's a lot more secure to carry and use. I keep a neck lanyard with a clip in my big bag of stuff for when I'm going to be in an environment where dropping my MT or knife would be a very bad thing (water, ladders, in the woods, on the roof, whatever.)
-
I like lanyards on small items so they are less likely to fall out of my pocket and are easier to grab hold of. Lanyards on MT's though are a PITA IMO so I don't put them on those.
-
@Benner said:
I like lanyards on small items so they are less likely to fall out of my pocket and are easier to grab hold of. Lanyards on MT's though are a PITA IMO so I don't put them on those.Yea, I noticed that most LM's have the lanyard ring at the tool end of the, erm, tool, meaning that when you have a screwdriver deployed the lanyard is hanging off the same end. Unless you hold the lanyard against the tool, it gets in the way. I really never understood why they designed the newer tools like that when the PST had it on the "correct" end.
I think the Swisstools have the lanyard hole near the pliers as well.
-
I like lanyards on small items so they are less likely to fall out of my pocket and are easier to grab hold of. Lanyards on MT's though are a PITA IMO so I don't put them on those.
Yea, I noticed that most LM's have the lanyard ring at the tool end of the, erm, tool, meaning that when you have a screwdriver deployed the lanyard is hanging off the same end. Unless you hold the lanyard against the tool, it gets in the way. I really never understood why they designed the newer tools like that when the PST had it on the "correct" end.
I think the Swisstools have the lanyard hole near the pliers as well.
I guess the logic with the lanyard rind included with the tools is that you can fold it away and forget about it if you don't want to use it. I agree that its a PITA if you actually try to use it though. The Crunch is the worst. Bears are worse than Leatherman!
The best lanyard ring solution by far has to be the detachable option on the Wave, Charge and Surge. You can have it all ways with that solution :)
-
i never used it so its been passed on, im not sure id trust it too much either :S more keen on the fixed one on the charge and wave
-
@ryan1835 said:
i never used it so its been passed on, im not sure id trust it too much either :S more keen on the fixed one on the charge and waveI used to be a bit mistrustful of it, but it's tougher than you might expect. Put another way, it takes a fair bit of pull to detach it, and if I had that much strain pulling on it, that might be the best option as opposed to following it!!!!
-
The lanyard ring on the tools side of the handles was probably supposed to be used with a lanyard with a clip, not a fixed one. That said, I still believe the lanyard attachment should be on the pliers side of the tool; hang a well-used MT by the end of one of its handles and just wait till gravity opens it up... :-\
-
i never used it so its been passed on, im not sure id trust it too much either :S more keen on the fixed one on the charge and wave
I used to be a bit mistrustful of it, but it's tougher than you might expect. Put another way, it takes a fair bit of pull to detach it, and if I had that much strain pulling on it, that might be the best option as opposed to following it!!!!
:P im not too fussed, im thinking of starting to lanyard it when im ontop of a lift but id need something that would give if it got caught and i carried on moving :/ maybe a pocket clips for the best :)
-
@Nikos said:
The lanyard ring on the tools side of the handles was probably supposed to be used with a lanyard with a clip, not a fixed one. That said, I still believe the lanyard attachment should be on the pliers side of the tool; hang a well-used MT by the end of one of its handles and just wait till gravity opens it up... :-\I hadn't even thought of that. Could you imagine a freakin SURGE just coming open? And it has some weight to throw around too. yep, they have to change it now, we're on to them.

-
I suppose that a lot of this boils down to whether you see a lanyard as a method of carry, or a safety net in case you drop it.
I'm definitely of the latter persuasion :)
-
I wont use a lanyard if my tool has a pocketclip. Otherwise i had to learn the hard way that a lanyard is needed: I lost my KF4 the only day i detached the lanyard from my belt - it just slipped out of my pocket in the metro.
If the tool has a proper pocketclip though, i will use that one as its a lot more convenient than untying the tool every time you want to pass it to a friend or reach something further away...
By the way: if you opt to keep lanyard attachment i suggest to attach an appriopriate bit of rope to the small hole where the lanyard ring is attached and get rid of the lanyard ring. The ring always annoys me as it adds quite a bit to the bulk of the tool and feel unconfortable while using some of the tools.
-
I dislike lanyard for the most part but i put them on my keychain, flashlight, multi tool, and folding knife. I don't use lanyard to pull out my equipment like other members on here. I had a surge fall out of my hand while in south america, it took me hours trying to fish the tool back from a narrow crevice. With that being said you can rig a lanyard so you can unwind a few inches giving you giving you a loop to wrap around your wrist.
-
One downside to a lanyard is: Finger smiths would think you may have an expensive Knife/tool
and in a sense you've given them the sign come and get me! :D -
then I would grab there hand and with the other knives I carry make them a Finger-less smith

Infact most of the time any
or :sak: is intriely concealed
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login