Charge tti
-
I have owned an ALX, and from what I understand they have the same gut hook serrated blade. I used the crap out of that guthook with no signs of wear or breakage. Sounds like you have a rare problem with that bridge breaking. It seems that the QC at Leatherman has had some problems(I didn't start this thread Davek! :D), but luckily for all of us their warranty is still top notch. I think they are starting to fix the problem, because my ST300 is stamped 0909, and it is flawless. What is the datestamp on your charge? All the Leatherman tools I had problems with were 08 models.
-
From what I've read, Leatherman totally outsources most of thier manufacturing to an extent, with the plier heads being made in Mexico, and the files somewhere in Europe..
I'm actually suprised that the folks over at QC haven't been outsourced themselves, especially from some of the horror stories that I've heard coming as of late from Leatherman..
Now I know why I treasure my original wave so much, when "made in USA" meant the absolute best..
Cheers,
Serge -
Its so shame to Leatherman,great tool but not so QC. ??? :-\
-
@Hkk said:
Just got a new charge tti today and have already have to send it in for repair the bridge on the guthook blade is cracked all the way through very dissapointed in such an expensive tool with such an obvious defect from the factoryYou will try a Swisstool or Swisstool Spirit,and you never be disappointed.
-
@Mercury said:
I have owned an ALX, and from what I understand they have the same gut hook serrated blade. I used the crap out of that guthook with no signs of wear or breakage. Sounds like you have a rare problem with that bridge breaking. It seems that the QC at Leatherman has had some problems(I didn't start this thread Davek! :D), but luckily for all of us their warranty is still top notch. I think they are starting to fix the problem, because my ST300 is stamped 0909, and it is flawless. What is the datestamp on your charge? All the Leatherman tools I had problems with were 08 models.Yes,they "fix the problem",actually if they fix one problem the tool returns with another problem,and etc.
-
LMs are not totally outsourced! The plier heads are from mexico because the company LM always used moved to mexico. So they continued to use them. Not sure on the file but everything else is done in Oregon.
-
also as far as get a vic and never be dissapointed? Thats a crock! I have a spirit and i dont like the thing. The plier heads are too thick to be usefull as needlenose. The drivers are weaker and slippy.
-
@jim guy said:
also as far as get a vic and never be dissapointed? Thats a crock! I have a spirit and i dont like the thing. The plier heads are too thick to be usefull as needlenose. The drivers are weaker and slippy.The pliers on Swisstool and Swisstool Spirit is very useful
,the drivers...yes,a little slippy,but useful too. :) -
the drivers are not as strong as LMs, ive twisted mine, and they twisted easy. Vic may have better qc than LM, but there tools are not as well thouht out as LMs. The drivers on my vic are no better than what LM had on their psts. I also dont like the pinned together construction.
-
Mine is dated 0110 I've got pics of the crack I'm talking bout but can't post them from my phone I can email them to someone and they can post them if they like ,I also have a spirit and love it and have a swisstool on The way I will always have the vics but also like trying otherthings to give them a rest and to have a back up incase there is a problem with one off them .
-
@jim guy said:
the drivers are not as strong as LMs, ive twisted mine, and they twisted easy. Vic may have better qc than LM, but there tools are not as well thouht out as LMs. The drivers on my vic are no better than what LM had on their psts. I also dont like the pinned together construction.I agree,LM have great drivers,but I can easily use ratchet
with 1/4 beats and not abuse tool drivers. -
Okay, a new debate!! At least we aren't arguing about plier heads. As far as LM parts being outsourced, I have to side with Jim Guy, I think they do outsource the plier heads, but only the casting part. The finish grinding is done in Portland. In fact, from what I've seen all their grinding is done in portland. As for the rest of the parts, I really have no idea. I would assume they outsource all cast parts, because it is cheaper to have a foundry do it than to do it yourself.
And the driver debate. I can honestly state that the phillips driver is the main reason I don't carry a spirit. It slips and galls way too easily. I have a LM blast that has seen around 500 screws, and you can't tell a bit. In reality, Vic drivers don't hold a candle to LM drivers. They're pretty, but ineffective. Don't get me wrong, I love Vics like no other, but their drivers just don't cut it.
-
@Mercury said:
Okay, a new debate!! At least we aren't arguing about plier heads. As far as LM parts being outsourced, I have to side with Jim Guy, I think they do outsource the plier heads, but only the casting part. The finish grinding is done in Portland. In fact, from what I've seen all their grinding is done in portland. As for the rest of the parts, I really have no idea. I would assume they outsource all cast parts, because it is cheaper to have a foundry do it than to do it yourself.And the driver debate. I can honestly state that the phillips driver is the main reason I don't carry a spirit. It slips and galls way too easily. I have a LM blast that has seen around 500 screws, and you can't tell a bit. In reality, Vic drivers don't hold a candle to LM drivers. They're pretty, but ineffective. Don't get me wrong, I love Vics like no other, but their drivers just don't cut it.
Thats why I like LM - they're useful

-
@jim guy said:
the drivers are not as strong as LMs, ive twisted mine, and they twisted easy. Vic may have better qc than LM, but there tools are not as well thouht out as LMs. The drivers on my vic are no better than what LM had on their psts. I also dont like the pinned together construction.
I agree,LM have great drivers,but I can easily use ratchet
with 1/4 beats and not abuse tool drivers.The point of a MT is to carry less tools, why would you even carry a MT if you can just use the ratchet?
I have owned an ALX, and from what I understand they have the same gut hook serrated blade. I used the crap out of that guthook with no signs of wear or breakage. Sounds like you have a rare problem with that bridge breaking. It seems that the QC at Leatherman has had some problems(I didn't start this thread Davek! :D), but luckily for all of us their warranty is still top notch. I think they are starting to fix the problem, because my ST300 is stamped 0909, and it is flawless. What is the datestamp on your charge? All the Leatherman tools I had problems with were 08 models.
Yes,they "fix the problem",actually if they fix one problem the tool returns with another problem,and etc.
I must disagree with you here. As many readers on this forum know, I have had my share of complaints with LM products. But never, NEVER, have they sent me back a faulty product, and if they did, I would have the decency to send it back and not mention the flub publicly. Their warranty is one of the best, and out of all the companies I have bought things from(which is a lot), Leatherman "respects" the consumer the most by asking minimal questions and making your warranty experience very easy. They treat every warranty like it is completely their fault, IE even when you step on your multitool to test it and break the plier head.
-
if i want a tool for the drivers i use the ST300, if its for the saw /files/blade i use the swisstool , i see me using the swisstool while camping etc , the st300 has been a very useful DIY tool, the LM's drivers are far better than the swisstools especially the Phillips,vic need to not polish the top section,

-
@jim guy said:
the drivers are not as strong as LMs, ive twisted mine, and they twisted easy. Vic may have better qc than LM, but there tools are not as well thouht out as LMs. The drivers on my vic are no better than what LM had on their psts. I also dont like the pinned together construction.
I agree,LM have great drivers,but I can easily use ratchet
with 1/4 beats and not abuse tool drivers.The point of a MT is to carry less tools, why would you even carry a MT if you can just use the ratchet?
I have owned an ALX, and from what I understand they have the same gut hook serrated blade. I used the crap out of that guthook with no signs of wear or breakage. Sounds like you have a rare problem with that bridge breaking. It seems that the QC at Leatherman has had some problems(I didn't start this thread Davek! :D), but luckily for all of us their warranty is still top notch. I think they are starting to fix the problem, because my ST300 is stamped 0909, and it is flawless. What is the datestamp on your charge? All the Leatherman tools I had problems with were 08 models.
Yes,they "fix the problem",actually if they fix one problem the tool returns with another problem,and etc.
I must disagree with you here. As many readers on this forum know, I have had my share of complaints with LM products. But never, NEVER, have they sent me back a faulty product, and if they did, I would have the decency to send it back and not mention the flub publicly. Their warranty is one of the best, and out of all the companies I have bought things from(which is a lot), Leatherman "respects" the consumer the most by asking minimal questions and making your warranty experience very easy. They treat every warranty like it is completely their fault, IE even when you step on your multitool to test it and break the plier head.
%100 agree!
:)
-
If there's a problem with your Charge TTi, send it in for warranty repair. I did so with my ST300 and they sent me a perfect tool back. They produce a boatload of tools and if a couple slip through the cracks with some problems, their warranty makes that acceptable IMO. If you decide to write them off, you'll be missing out on the best tools!
-
Sorry to hear about your damaged tool Hkk - sounds more like it got broken than a QC issue tbh - where did you get it from? I've not heard of a problem like that one before.
@sergemaster said:
From what I've read, Leatherman totally outsources most of thier manufacturing to an extent, with the plier heads being made in Mexico, and the files somewhere in Europe..You should read more reliable sources ;)
Leatherman's plier heads are indeed now cast in Mexico, since the company they have always used moved there. There has been suggestion that some files were made somewhere in Europe, but I've yet to see any actual evidence of that as opposed to speculation. During the 1980s, some PSTs and Minitools were made in Japan. The vast majority of parts are manufactured, and all assembly of the tools takes place in Oregon.
So any perceived "QC problems" are "Made in USA".
-
@DaveK said:
Sorry to hear about your damaged tool Hkk - sounds more like it got broken than a QC issue tbh - where did you get it from? I've not heard of a problem like that one before.From what I've read, Leatherman totally outsources most of thier manufacturing to an extent, with the plier heads being made in Mexico, and the files somewhere in Europe..
You should read more reliable sources ;)
Leatherman's plier heads are indeed now cast in Mexico, since the company they have always used moved there. There has been suggestion that some files were made somewhere in Europe, but I've yet to see any actual evidence of that as opposed to speculation. During the 1980s, some PSTs and Minitools were made in Japan. The vast majority of parts are manufactured, and all assembly of the tools takes place in Oregon.
So any perceived "QC problems" are "Made in USA".
I thought it was common knowledge that they assembled all the tools in Oregon. This is what happens when people read an opinion and their mind transforms it into misplaced fact. If you check out LM's website, they will tell you they assemble everything in the Portland Factory, right down to the super sturdy clamshells.
Hkk, I sent my Blast in last week on 5-26, and they sent it back out to me yesterday. It should be here no later than next wednesday or so. That's a pretty quick turnaround. Good luck with your warranty return, it should go smoothly.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login