Show off your multitool mods!
-
@ryan1835 said:
the tools are pretty much just the same just longer and thick arent they dave?As the pocket clips?
Not quite - the proper tools are made from tool steel and are therefore less likely to strip teeth etc. They also have the small screw fitting at one end, and the larger size at the other.
For the Micra I have the LM issued sockets.
You can see them here after helping me to take Ben;s Supertool and Micra apart (when he pays me I'll put them back together :D):
Knurled Screw tools (top):

Micra Socket:

-
what are the tools near the mini in this pic then dave?

-
Blimey - where did you find that pic? Lol.
OK - there are two small ratchets which appear to have some sort of torx bits in them, the black handled tools are 5-pointed security torx, and the sockets either side of the top one are the Micra sockets you can see on the ratchets in the pic I posted earlier :)
None of them have anything to do with the PST that is in bits at the bottom of the pic, so I guess I'd been disassembling something like an old Charge or a Sideclip or something before hand - honestly can't remember

-
that "was" going to be my pst lol you pm'd it a while back and for some reason the tools look cool :P
-
I just snapped one of those security torx tools on a stubborn old Charge XTi ::)
The ebay seller no longer ships internationally either :(
-
That's very kind Ryan - but Raptorman has offered to order me a couple of sets. Besides, owning a Sideclip, you never know when you might need them again :)
-
if your sure :P
-
I've just completed a little project I've been working on and deliberating over for months! It all started with an old knackered Charge XTi that I picked up on ebay a couple of years ago. The pliers were knackered, blades were scratched and worn, and somebody had clearly tried to fix it up a bit before I did as a couple of the pins in the centre of the security torx fittings (the 5 pointed ones) were snapped off and the screw heads rounded etc, etc.
They also seem to have used some thread locker that is stronger than my security torx tools (two broken on this project, including one of the ones Ryan sent me the other day) :( So yesterday, I decided ot bite the bullet and drill the fixings out - I got through a few bits, but got there in the end.
I'd accumulated most of the fittings and tools I needed for my mod and when the scissors that Gareth sent me arrived this morning, it was time to finally build it.
Ladies and Gents, I give you... the Charge DTi (geddit? :D)




So we have a nice S30V blade, crimperless plier head, black fixings (now 6-point instead of 5) with the internal tool selection of the Charge Ti / TTi. So I guess that makes it a Ti with premium S30V blade and cutting hook, or a TTi without the crimpers!
I like DTi ;)
-
That looks great Dave

While I have no problem with the crimper in the plier head if I was given the choice I'd probably go with out.
-
A most fine
resurrectionreimagining sir :D -
Impressive work there mate

-
Good work Dave..

Now put on those 2HO blades and send the DKti to me.. ;) :D -
you only got those torx tools yesterday

:D
nice mod dave

-
-
chromed plastic doesn't come cheap :P
-
Very nice Dave.
Might even be nearly as nice as a modded Kick. ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
