Leatherman Charge Ti Rebuild
-
excellent job on the Charge, it's beautiful.
-
I can take more pics.
It would be easier with 2 torx bits but may be possible with one, if you open the tool(s) it locks the shaft allowing the screw to turn. You are aware that one of the screw heads is part of the shaft, look at my picture.
I used a 3 stage process with varying grades of cotton mops and compounds.
I will add photos soon if anyone is interested.Once it is apart you can lightly file either the liner lock or the back of the blade until it fits but try and make the finish nice and smooth so that the liner slides across the rear of the blade or you may end up taking a little too much off.
@IrishMike said:
WOW! Any more pics?
What did you use to polish the tool?
I just got a used Charge tti and I have problems with the tool sticking a little when opening.
I also have an issue with the liner-locks not deploying fully on the Serrated blade, saw and file.
I only have 1 security 10 torx, is the dis assembly/reassembly process a nightmare? I've been thinking about doing more work after a good dousing with WD-40 and trying to breaking-in the liner-locks by using them over and over while killing time does not seem to be helping much.
I know there are other threads about the liner-locks not deploying fully so any help you could provide would be useful.
Beautiful tool!
-Mike
-
Alternatively, you can pick up torx drivers from Amazon and ebay, sold as Leatherman Wave tools. Theyt're cheap and cheerful but do the job - just make sure you get the right ones.....
The earlier Ti models woudl use a 5-point security torx, whereas the later models (including the TTi) use the 6-point security torx tools.
Personally, I'd take it apart simply to appreciate what goes into the Charge - they are an engineering marvel!
-
I completely agree, once I had stripped one down I never again put up with the little flaws like liners etc.
Halfords in the UK and other car shops sell the bits too, I have in the past bought 2 rails of security bits £30+ just to strip and reassemble a tool when I have been away from home, done the job and then taken the told back for a refund.
But the little issues are easy to fix and I have given the same treatment to 2 waves and a surge they are now how they should have left the factory.
I shouldn't complain as they already cost quite a bit anyway and i loath paying extra when I can do it myself. -
Glad it made it...looks great.
-
Thanks mate, good to have a Ti back.
Nice job on the sharpening, what did you use? -
Can I just say every time I come into this thread I find myself looking more at your avatar than at the actual content?

-
The delightful Cheryl Tweedy, got to love her xx
-
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
Serge -
I don't think so as the construction is the same across all the titanium charges I think it's just screw tension issues.
I could stand to be corrected though. -
Perfectly useable edge mate.
I am a little anal about the edge on most of my knives, I usually freehand with varying grades of diamond stones, then hard and soft Arkansas then loaded and dry strops.
With MT blades they get so much use that I keep them just about shaving sharp so this one just got lightly touched with the ceramic side of a DC4 and then a loaded strop
Any sharper than that and I slice bits off the side of my fingers as I open and close the blade almost OCD like as I am watching TV -
@sergemaster said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?Cheers,
SergeYup, but not just the file. On my Ti, the serrated blade scrapes against the inside of the handle and the blade actually has small scrape lines now. :( Thankfully, the clip point blade is fine.
Anyways, nice work on the Ti, Viw9419. It looks good!
-
Thanks mate.
-
@sergemaster said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
-
Nice job, very kewl polish job as well.
It always takes me double time to read your posts
because I find that avatar so distracting. :) -
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
And I've got numerous Charges and none of them do. Weird huh?
-
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
@Grant Lamontagne said:
I remember reading that the Charge TI had allot of issues, hence why it was retired and replaced wit the TTI. One one of the issues was that the file would actually scrape against the liner unless you pushed it to the side as you closed it.. Washer issues maybe?
Cheers,
SergeI have numerous Charges and they all rub. It's got nothing to do with the individual model and more to do with design and construction.
Def
And I've got numerous Charges and none of them do. Weird huh?
Mine does rub, might have something to do on which market they are going. Might be rubbing on the American market and none on the European market.
-
Maybe, but it's more likely that I've been lucky, or more likely still it's because just about all of my tools are 2nd hand / used and they may have been tweaked / adjusted by the time they get to me - I'm not sure.
That said, the few I have had from new seem fine too! Clearly many people haven't been so fortunate though.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login