Multitool TLC
-
Man-o-man, what an overhaul!
Anybody else got some useful tips for revitalizing a code blue multitool?
-
I have admired that post since he first posted it. It goes to show that even a tool in the state that was in can be retrieved if you put some TLC into it. It also shows that a bit of surface rust is not the frightening thing some folks seem to have about it, that was in a very bad condition but it only had the 2 small pits when Spoonrobot had finished with it. With his care and attention it should now last for years.
Dave
-
Been at this site less than a week and already seen half a dozen mentions of using WD-40 to care for tools.
I suppose I can't hold it against Americans to use an American product, but the real stuff, the good stuff, the stuff they (should of) used in 'nam is Inox.
http://www.inox-mx3.com/inox.htm
MX4 and MX5 are the Anti-Corrosion Champs of the lot.
-
I mentioned INOX in my Care and Feeding for SAKs, and while I do appreciate it, I have found little benefit for regular maintenance over regular mineral oil, available at any grocery or pharmaceutical store. The penetrating compound that was added to the mineral oil to make it INOX is nice on older tools that are stiff due to corrosion or an accumulation of crap, but with mineral oil being so much more readily available (and cheaper!) I don't go through a lot of INOX.
I do like that it's food safe though- that's always a bonus point.
Overall I try not to use oils for lubrication because of the increased amount of stickiness they create, and allow more nasty stuff to gather in moving joints. If a lube is needed for everyday carry (as opposed to restoring mobility to an old/abused tool) then I usually opt for powdered graphite, available at any locksmith or hardware store simply because pocket lint, dust etc won't stick to it.
Def
-
Hey Def, I just did a google on powdered graphite (I haven't used it before), and saw that one site claims that:
"Graphite powder, although it is an excellent dry lubricant, has been shown to be corrosive to aluminum when there is possibility of moisture being present."
Has anyone used this with any tools that have aluminum scales? And has it been "corrosive"?
Just wondering... -
I can't say as I've ever noticed it, and I have used it on SAKs. The liners of SAKs are aluminum and I've never had a problem, which is odd because there is so much moisture in the air here steels rust pretty quick.
Def
-
@Defender said:
I can't say as I've ever noticed it, and I have used it on SAKs. The liners of SAKs are aluminum and I've never had a problem, which is odd because there is so much moisture in the air here steels rust pretty quick.Def
Hmmmm.... Well, good to hear.

-
You have me curios now though- I think I may have to devise a devious experiment!

Def
-
@Defender said:
You have me curios now though- I think I may have to devise a devious experiment!
Def
You always were a wild one Def! What do you have in mind?
-
I dunno... thinking about graphite powder, a few aluminum rods I have, and maybe leaving them out on the deck for a month or so. Some time lapse type shutterbuggery...
Or instead of the rods I have a few old SAK liners laying about.
Def
-
I got a fresh tube of graphite today, and the gentleman at the locksmith shop I bought it from has never heard of reactions with aluminum either, and considering the moisture/humidity in Nova Scotia, a locksmith would likely have seen it if it was there!
Of course, aluminum is too soft to normally be used in locks, so I will test it on an old SAK liner I have lying around. I'll polish and clean it up first, then take some "before" pictures.
Given that very few multitools have aluminum in them I think the SAK liner is the best candidate for this test, especially considering the most prominent aluminum multis are anodized for protection, and the aluminum isn't structural, so any corrosion wouldn't be worth worrying about.
Def
-
Sounds like a good test!

-
THE WAY I GET RUST OFF KNIVES AND TOOLS
I get a plastic cup.. Then put in some white wine vinegar.. Then put a few tablespoons of baking powder in the vinegar.. Then get a Q-Tip and dip the desired end into the solution and apply directly to the rust.. Will come off immediately!
-
-
O haha: no LM's! But I really never had a problem with rust but only on my knives.. Like the high carbon ones
-
Customer come in with Charge asking for a service - all rusty and messy (easy to solve), also FULL OF SAND!
Best way to get sand out?
I was thinking compressed air, but it is in pretty good, all under the scales. No blades move without making gritty sounds ??? ???
-
@Nomad said:
Customer come in with Charge asking for a service - all rusty and messy (easy to solve), also FULL OF SAND!Best way to get sand out?
I was thinking compressed air, but it is in pretty good, all under the scales. No blades move without making gritty sounds ??? ???
Ugh! Sand is the WORST enemy of a multitool.
Best would be a total disassembly and a good cleaning. If that ain't practical, go with the compressed air and pray. -
Time to dig up my Security bits and have a hot date with a Charge then!
-
I'm almost as bad as Dubya Dawg, with this double posting.
My Security (well not my, some I borrowed) bits didn't fit -
It's possible they were just rubbish bits, and not accurate enough to actually work - or is it possible that Yuessayans use a different size security bit? -
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
