Thetopher's surge project
-
Thanks for the Mod update,and welcome to the forums Thetopher.

-
Wished there was a touch up pen or something for black oxide, as I too would like to file down them squared edges.
-
Thetopher,
Welcome

Its always good when you mod a tool to work a bit better
-
@Xelkos said:
Wished there was a touch up pen or something for black oxide, as I too would like to file down them squared edges.Sharpie?

The only time I have ever held a Surge, the first thing that crossed my mind was all of the sharp edged that I don't feelon my ST200.
I wonder why they don't round some of them in the production process?
Welcome to the forums!
-
Debated the idea of the sharp squared edges on my BO Surge, and figured my comfort was more important than how the tool looked. Only got the BO version as with free shipping it was cheaper than any other Surge I could find.
Got out the metal and diamond files and went down the edge of the handles & the two knife blades. Also touched up the blade exchanger thin metal piece with the Surge's diamond file. Now to get my ceramic stones out and go over it.
Sure feels a lot better, even though the BO Surge now has pin stripes.

-
Thanks for the replies, guys!
Evil, I'd love some more info about the riveting you did to get the spring back in. I actually want to try and replicate your Supertool head mod later down the road when I have more money.
Xelkos, the pin striped BO actually sounds pretty nifty looking. The diamond file was actually what I used to do the initial filing on the stop to make the blade exchanger close properly. I think the fact that it's removable makes it 10x as useful as a fixed file. Bear in mind the rattle and blade stop were repaired about 30 seconds after opening the package, while I sat in the company truck in the Sears parking lot. I'm one of those guys that enjoys fixing things more than actually using them.

For now I've been working the blades back and forth, I want to wear the pivot surfaces as close to smooth as possible before I pull the knives off and clean/oil the mating surfaces. The fit and finish is still nowhere near my Powerlock, but it's getting there!
-
@thetopher said:
Xelkos, the pin striped BO actually sounds pretty nifty looking.Would of been 'cept I had to do it by hand. If I would of had a small dremel-like power tool with buffers would of looked a lot better.
@thetopher said:
The diamond file was actually what I used to do the initial filing on the stop to make the blade exchanger close properly. I think the fact that it's removable makes it 10x as useful as a fixed file.
Now you've given me an idea, 'cept I don't have the cutter ability. Make a small handle with a blade changer on the end of it, then could use the T-shank and files like a regular file. Can slip it into the back of the sheath when not in use. 
Yet I don't have the material or ability to cut out a handle and fit a blade holder onto it. Would make a nice project for an enterprising individual that has a shop. Could make a few bucks on the side if they could produce them for sale.

-
I do exactly the same with everything that arrives here - immedately check it over and decide what's wrong with it, then start messing with it to make it "right" :D
I think you have done and great job topher, and that have also got the measure of us ;)
-
Alright, so I finally had a little free time and I decided that having a piece of cardboard in my Surge to keep it from rattling was unacceptable. So I pulled the cardboard shim out and slipped a pick underneath the spring, then used a small screw driver to twist the pick until it lifted the spring up. While it was up I used a nice fat hex key to bend the end of the spring back down for more tension. It worked like a charm.
Onto the pics, which I think turned out a little better this time around.
The tools I used

and the setup...

Maybe when my company starts paying me I can do some actual modding, instead of just finishing the job Leatherman should have done at the factory. :D
-
@thetopher said:
Thanks for the replies, guys!Evil, I'd love some more info about the riveting you did to get the spring back in. I actually want to try and replicate your Supertool head mod later down the road when I have more money.
*Hey thetopher. Sorry I did not read your post again until just now. Seems you sorted out the spring rattle on your own just fine though
Depending on which future mods you have planned for your Surge, the rivets will have to be removed and replaced. Keep up the good work.....~ evil ~*
-
Thetopher
Is the leather belt you used fitted to your 1'' belt sander?
If so I think I need one of these
My sander looks a lot like yours (with out the grips)
-
@sparky415 said:
Thetopher
Is the leather belt you used fitted to your 1'' belt sander?
If so I think I need one of these
My sander looks a lot like yours (with out the grips)
It is fitted, it's a 1" X 30" belt. You can pick them up from just about any knife making supplier. That particular one is a "Surgi-Sharp" that I got on Amazon. They come in other sizes too.
-
Thanks for that

I will see if I can find one over here
-
I was always disappointed with the Surge's lack of a bottle opener, but I had hoped I could use the can opener in a pinch. To find out, I attempted to try it on a beer bottle after work. I managed to open it, but it was quite an ordeal. By punching a hole in the top of the cap and prying sideways I finally got the cap to pop off. At least after all the hassle I got to enjoy a beer!
So, there are two major gripes I have with the can opener on my Surge:
1: It's designed to open cans and not bottles
2: It's a royal pain to open, since it lacks a thumb notch.
So this is what I did to resolve the matter.
In this picture I have it next to the bottle opener on my Powerlock to compare profiles.

So I started by grinding down the tooth on the can opener to make it more "bottle friendly"

Then I added a thumb notch, I also filed the end down into a small screwdriver point. Not that I'll ever need it with the Surge's bit driver, but I figured "Why not"
Here's the finished product!

As you can see, the thumb notch is very accessible and easy to get to, making this tool much more convenient to use.

Thanks for reading!
-
Hmm, I lay the can opener to where the bottle cap is more flat with the grading of the tool. The pop it off on an angle. Still it's an interesting idea you have there.
An easy method than making a bottle opener bit or tool exchanger. :)Should go and try and find me a keyhole and coping-saw-like blade and get them converted over, and a metal saw too. Haven't seen any of them rip-grip type blades around here, the ones with the gnarly grit infused on the blade's edge. Really like the MUT's design of the saw. Would like to find something like that to use in the tool exchanger.
-
I have the same shaped can opener on my SuperTool 200, and It has opened bottles just fine as it is.
I just use it like a regular bottle opener and it works just fine. -
All my attempts to open bottles with it resulted in a hole in the top of the bottle cap. Perhaps I have a rookie bottle opening technique

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login