Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Bended corkscrew

Scheduled Pinned Locked Moved Swiss Army Knights Forum
17 Posts 1 Posters 2.9k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Bended corkscrew
Bended corkscrew
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ryan1835 Offline
    ryan1835
    Posts: 5,223
    ryan1835 Offline
    ryan1835
    wrote on last edited by
    #6 Quote Reply

      temper of a corkscrew :rofl:

      1 Reply Last reply
      • stressmaster5000 Offline
        stressmaster5000
        Posts: 3,414
        stressmaster5000 Offline
        stressmaster5000
        wrote on last edited by
        #7 Quote Reply

          I have used the felinevet way with much success. Use a vice grips pliers and clamp down on the corkscrew base when in the opened position and take a large pin punch that will fit inside the corkscrew snugly and slowly bend it straight. Small movements and rechecking is better than a large movement where it might snap off.

          1 Reply Last reply
          • Neil Offline
            Neil
            Posts: 15,287
            Neil Offline
            Neil
            wrote on last edited by
            #8 Quote Reply

              @stressmaster5000 said:
              I have used the felinevet way with much success. Use a vice grips pliers and clamp down on the corkscrew base when in the opened position and take a large pin punch that will fit inside the corkscrew snugly and slowly bend it straight. Small movements and rechecking is better than a large movement where it might snap off.

              So putting it in a vice and smacking the crap out of it with a hammer is bad? :( ... oh :-[

              :D Tim's method as Wayne outlined above works very well. You should have it ship shape in no time :tu:

              1 Reply Last reply
              • Spork, Lord of Lime Jello! Offline
                Spork, Lord of Lime Jello!
                Posts: 3,516
                Spork, Lord of Lime Jello! Offline
                Spork, Lord of Lime Jello!
                wrote on last edited by
                #9 Quote Reply

                  I clamp the base in a vise so that there is no strain on the pivot when tweaking the worm.

                  corkscrew03.jpg

                  1 Reply Last reply
                  • VicX Offline
                    VicX
                    Posts: 169
                    VicX Offline
                    VicX
                    wrote on last edited by
                    #10 Quote Reply

                      @Herman said:
                      This morning I picked up a Cybertool 34 without scales. It's in excellent condition except for the corkscrew which is completely bended. Does anyone know an easy way to fix this (without causing further damage)? Thanks!

                      As all the other guys said, clamp the SAK and bend the corkscrew back to its original shape. But do it slowly! :)

                      VicX

                      1 Reply Last reply
                      • glorn Offline
                        glorn
                        Posts: 1,223
                        glorn Offline
                        glorn
                        wrote on last edited by
                        #11 Quote Reply

                          @Spork, Lord of Lime Jello! said:
                          I clamp the base in a vise so that there is no strain on the pivot when tweaking the worm.

                          That's exactly how my ex-girlfriend did it too. I should call her.

                          1 Reply Last reply
                          • Herman Offline
                            Herman
                            Posts: 129
                            Herman Offline
                            Herman
                            wrote on last edited by
                            #12 Quote Reply

                              Tadaa!!
                              It worked out pretty good, so I don't have to throw it away now :)
                              Thanks for your support :cheers:

                              cybertool.jpg

                              1 Reply Last reply
                              • stressmaster5000 Offline
                                stressmaster5000
                                Posts: 3,414
                                stressmaster5000 Offline
                                stressmaster5000
                                wrote on last edited by
                                #13 Quote Reply

                                  Good job! :tu:

                                  I have straightened a couple myself. It usually works out pretty well as long as you take it nice and slow.

                                  1 Reply Last reply
                                  • Mike, Lord of the Spammers! Offline
                                    Mike, Lord of the Spammers!
                                    Posts: 42,975
                                    Mike, Lord of the Spammers! Offline
                                    Mike, Lord of the Spammers!
                                    wrote on last edited by
                                    #14 Quote Reply

                                      Good job mate :tu:

                                      1 Reply Last reply
                                      • VicX Offline
                                        VicX
                                        Posts: 169
                                        VicX Offline
                                        VicX
                                        wrote on last edited by
                                        #15 Quote Reply

                                          @Herman said:
                                          Tadaa!!
                                          It worked out pretty good, so I don't have to throw it away now :)
                                          Thanks for your support :cheers:

                                          :cheers:

                                          1 Reply Last reply
                                          • bren10man Offline
                                            bren10man
                                            Posts: 767
                                            bren10man Offline
                                            bren10man
                                            wrote on last edited by
                                            #16 Quote Reply

                                              Thank you for these instructions.

                                              I won a 1980's vintage Woodsman on E-bay about a month ago, and it had a bent corkscrew.

                                              It is not 100% but I would give it a 98% bent back to where it needs to be. It no longer touches where it shouldn't. I do not want to go further, for fear of breaking a grooved and vintage corkscrew on a vintage Woodsman.

                                              1 Reply Last reply

                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                              With your input, this post could be even better 💗

                                              Register Login

                                              1. Home
                                              2. Tool Talk
                                              3. Swiss Army Knights Forum
                                              4. Bended corkscrew
                                              Reply
                                              • Reply as topic
                                              Log in to reply
                                              COMMUNITY LINKS
                                              EDC-TV SAKWiki GearFeed SAKSelector
                                              Operational Funds

                                              Help us keep the Unworkable working!

                                              Make A Donation
                                              November Goal: $300.00
                                              Due Date: Nov 30
                                              Total Receipts: $0.00
                                              Below Goal: $300.00
                                              0% funded
                                              • Login

                                              • Don't have an account? Register

                                              • Login or register to search.
                                              • First post
                                                Last post
                                              0