Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Rivited multitools

Scheduled Pinned Locked Moved General Tool Discussion
9 Posts 1 Posters 1.7k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Rivited multitools
Rivited multitools
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • edap617 Offline
    edap617
    Posts: 3,958
    edap617 Offline
    edap617
    wrote on last edited by edap617
    Quote Reply

      What's your opinion as to why some multitools are rivited while others are screwed or bolted? What are the advantages and disadvantages?

      Leatherman use torx screw on most models except the Squirt and Juice. Most if not all Gerber and Sog multitools are bolted. Victorinox, Buck, Schrade, Kershaw are all riveted. Am I right?

      Edap

      1 Reply Last reply
      • Biru Offline
        Biru
        Posts: 618
        Biru Offline
        Biru
        wrote on last edited by
        #1 Quote Reply

          EDAP:

          I had nearly this same post a while back. I was looking at a new job and wondered whether my Victorinox, with its rivets, would be as strong as my Bear Jaws, SOG Powerlock or my Supertool- all of which are bolted together. The general consensus of the posters was that the Victorinox rivets are very strong and that the tool would tear up or break before the rivets would. My Swisstool had a couple of tools that were just right for the job and I do love my Swisstool. Having said that, I have to be truthful when I say that I trust the bolted tools more, though there is no rational evidence to support that trust. I guess the small diameter bolt which threads into the pivot of the bolted tools could strip or break just as the rivet could. I didn't really answer, but these are just my opinions. Regards, Bill.

          1 Reply Last reply
          • Benner Offline
            Benner
            Posts: 28,081
            Benner Offline
            Benner
            wrote on last edited by
            #2 Quote Reply

              I don't think that either is stronger, but that the bolted ones are far more convenient to dismantle and clean, and for the repair staff to fix.

              1 Reply Last reply
              • J-sews Offline
                J-sews
                Admin Team
                Posts: 23,224
                J-sews Offline
                J-sews
                Admin Team
                wrote on last edited by
                #3 Quote Reply

                  Why do different manufacturers use different assembly methods? Must be each one uses the technique that they are most familiar with. Victorinox for instance makes millions of riveted Swiss Army Knives, so they no doubt have the equipment and expertise to use rivets on their multitools.

                  1 Reply Last reply
                  • Sea Monster Offline
                    Sea Monster
                    Posts: 4,261
                    Sea Monster Offline
                    Sea Monster
                    wrote on last edited by
                    #4 Quote Reply

                      Rivets prevent Joe-jackhole from dismantling his tool and sending it back to Vic with a big cry about not being able to fix it again - Rivets can also be ground down flush and polished, which some may find appealing. Rivets also don't run the risk of loosening during general use. Rivets won't shear or gore as threaded fastenings can.

                      When it comes to building steel bridges and tankers, Rivets are the chosen fastening, whether this is because they are cheaper or faster is not known to me, but they're obviously up to the task of load bearing, even if they don't take advantage of fabulous inclined plane technology.

                      1 Reply Last reply
                      • prime77 Offline
                        prime77
                        Posts: 2,887
                        prime77 Offline
                        prime77
                        wrote on last edited by
                        #5 Quote Reply

                          I agree with what Bob said. I think it's just what the tool makers are used to and have the equipment to do. Having said that I can't imagine what the Vic Spirit would look like with it's sleek lines taken away with either the LM curled screws or the SOG bolts. I like the rivets on it.

                          1 Reply Last reply
                          • Spoonrobot Offline
                            Spoonrobot
                            Posts: 1,894
                            Spoonrobot Offline
                            Spoonrobot
                            wrote on last edited by
                            #6 Quote Reply

                              I dislike rivets, or really any thing that keeps me from dismantling my tools, knives or flashlights.

                              Example, today I found an odd duck Buck 360 that has a broken lock spring so the tools on one side of the handle flop around loosely. If this tool were screwed construction I could merely tighten the fasteners as a stopgap measure and then eventually disassemble the tool and repair.

                              1 Reply Last reply
                              • Biru Offline
                                Biru
                                Posts: 618
                                Biru Offline
                                Biru
                                wrote on last edited by
                                #7 Quote Reply

                                  Rivets I'd imagine are chosen because they are faster. You simply put the insert into the socket, press and you're done. I'd guess you could do three rivets in the time it takes to thread and torque a bolt. I'm not really dissing the rivets. As I previously said, I haven't had a rivet come apart during use. It just seems the press fit of the rivet would be a bit more suspect that the thread attachment of the bolt.

                                  1 Reply Last reply
                                  • Tom Munch Offline
                                    Tom Munch
                                    Posts: 1,384
                                    Tom Munch Offline
                                    Tom Munch
                                    wrote on last edited by
                                    #8 Quote Reply

                                      I suspect the rivets can be more precisely controlled for tolerance in the shop - especially if they're using CNC machines. It seems to work very well for Vic. Their consistency of manufacture is excellent!

                                      Tom

                                      1 Reply Last reply

                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                      With your input, this post could be even better 💗

                                      Register Login

                                      1. Home
                                      2. Tool Talk
                                      3. General Tool Discussion
                                      4. Rivited multitools
                                      Reply
                                      • Reply as topic
                                      Log in to reply
                                      COMMUNITY LINKS
                                      EDC-TV SAKWiki GearFeed SAKSelector
                                      Operational Funds

                                      Help us keep the Unworkable working!

                                      Make A Donation
                                      November Goal: $300.00
                                      Due Date: Nov 30
                                      Total Receipts: $0.00
                                      Below Goal: $300.00
                                      0% funded
                                      • Login

                                      • Don't have an account? Register

                                      • Login or register to search.
                                      • First post
                                        Last post
                                      0