Evil's New Bit Project: To go where no Leatherman bits have gone before.....
-
Speaking of being a tease, when are you going to show us pics of that pocket knife of yours?

-
*Hey gang. Evil here again. Ok, now that I've shown you the new bit card here are the new drivers that it holds. Often when I assemble/disassemble, I find that I need long reach drivers. I set out to create a solution that the other typical options would not solve. All too often when you need access to a recessed fastener, it is down deep in a narrow hole. If your multitool happens to have dedicated long reach narrow drivers you could try that, but what if even they were not long enough? If you have the bit set, you could use the bit extender. Now you have the length but the bit extender itself prevents access because of the width. Some may be looking forward to adding the new MUT double-ended extended bits to their arsenal. Sorry to disappoint you, but while these will indeed have reach, they too suffer the downfall of being able to fit into narrow holes. Any hole more narrow than the bit itself and you are screwed, no pun intended. By design, they need the full width on each end on order to be held in place. Despite this fact, I actually made a double ended long driver for my new pocket knife for versatility. This kit will supplement my Skeletool, Wave, Surge, my new pocketknife project, as well as my extended bit driver (with handle) for the times when a long reach narrow driver is called for. Granted, my new drivers only have a single driver tip, but this was necessary in order to solve the issue. Made out of D2 toolsteel, these are a full 3" long. Flat drivers are hollow ground. Another goal when I set out to do this project is that it take up no more room than a standard bit card. I wanted it to compliment my other bit cards and easily be stored alongside them. I could have used a standard set of 1/4" long reach drivers in conjunction with the extended bit driver but that is more real estate than I was willing to give up in my EDC and still would have had to come up with a larger, bulkier storage system. I will tinker with different lengths and driver tips if the need should ever arise, however, I have found that this setup suits my needs perfectly at the moment.....
~ evil ~
Dedicated extended drivers on my Surge and Wave. These solve my long reach issues a majority of the time, however, there are occasions where even these are not long enough......*

New bit card with extended drivers.....

*My new extended drivers in the sizes and configurations that I use the most.....*

Here is the group shot of my new extended drivers alongside some of my other custom bits. When being stored, they stack nicely.....*

Installed on my Skeletool.....*

In creating these, I save trips to the toolbox. Sure, I could go to the toolbox for a "real" screwdriver, however, I live by the mentality of always being prepared as possible. For the little real estate that these occupy in my EDC these have proven their usefulness and worthiness by being able to go where no Leatherman bits can go..... ;)
-
Those are great and practical,as a retired acft mech I know the value of thin extended bits,so far I have liked all your mods,do you work in a machine shop or ???
& 
-
That is great

-
Very cool... again :D
Slight aside, I think you could do with making your watermark a little less intense and perhaps offset, presently it detracts from the image. Just my opinion of course :)
-
@Smitty44 said:
Those are great and practical,as a retired acft mech I know the value of thin extended bits,so far I have liked all your mods,do you work in a machine shop or ???
& 
*Thanks Smitty! Yes, they have become quite handy. No machine shop, just my garage..... *
*Thanks Benner!
*@Neil said:
Very cool... again :DSlight aside, I think you could do with making your watermark a little less intense and perhaps offset, presently it detracts from the image. Just my opinion of course :)
Thanks Neil! Point taken on the watermark and am still playing around with different designs. Not only do I do traditional airbrushing, I do digital airbrushing as well and know how easily a basic watermark can be removed. Done on purpose, this is me discouraging those efforts..... ;)
-
I do understand your reasons for watermarking, but no picture is photoshop proof. I'd have no problem removing the watermark on any of those photos if I for some reason wanted to, so they do more to make it hard for honest people to see the pictures than they do anything else.
Besides, "evil" is a common word, if someone wants to steal them all they really need to do is make a nick like evil_smurfo and post them someplace else.
Not meant as criticism, just a sad truth about copyrights
-
@Andreas said:
I do understand your reasons for watermarking, but no picture is photoshop proof. I'd have no problem removing the watermark on any of those photos if I for some reason wanted to, so they do more to make it hard for honest people to see the pictures than they do anything else.*You're right, no picture is photoshop proof. It will however deter the less experienced person from removing a watermark. And honestly, I am totally ok if the viewer only gets the idea of the photo while visibly protecting details I would want to protect.....
Yes, "evil" is very common indeed. It is something I am just using for now. Even just a few months ago all of this multitool stuff was just a mere hobby. I am finding myself devoting more time to it as of late. I have a whole other business and livlihood outside of this. If I can start to use multitools in a way that can earn me income then I will more than gladly go the whole nine yards and create a business out of it. And yes, the truth about copyrights is a sad one.....*
-
I figured this is what you were doing. Good show :)
I'm thinking about going the Slack-ier direction with something like this, and just grinding the end of some normal electric driver bits to fit the large driver. Something like a 3" or 4" #2 Phillips bit should do it for me.
-
Thats nice work with that ambigram :)
-
That's clever

-
I just couldn't help but notice the symmetry in the watermark :D
-
Evil,
How did you make or attached the lip on your knife blades? Is it only the screw or is there a micro pin involved as well - to prevent it revolving around the screw?Do you perhaps have a close-up photograph? I would like to do something similar to my Wave.
-
Really nice work on the flat drivers
-
I don't suppose, Mr. Evil, that you might be willing to make another set of those extended bits with the card to sell to me, perhaps? :)
What does it take to get started making these things for oneself, anyhow?
-
It seems that Evil haven't been active for a while here, but hopefully he'll find his way back someday.. :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
