Show off you flashlight mods!
-
Well, I am not technically savy enough to do home-built mods myself. I usually buy them already done or Lego things up. This first one I put together piece by piece as money allowed.

It's a PEU Pineapple body which has a McGizmo McTC tailcap with a single stage McClicky module installed. It's all topped by a Tactical Lighting Solutions Striker Bezel unit with a CREE Q5 LED emitter. It's all Surefire E-Series compatable. Here it is alongside my slightly legoed Surefire 6P Defender (this SF uses a 6PD body and head, but the head now houses a Solarforce CREE R2 drop-in. Attached is a Detonator cell-extender and a Leef tailcap with a single-stage McClicky tailswitch).....

Another that I have is a ElektroLumens modded 3D Maglite. It's the black one with the huge bezel.........


It started life as a regular stock 3D Incan Maglite which Wayne over at ElektroLumens did his magic to. He basically cuts off the switch holder light post, wires up the switch and LED directly, and presses in a custom made heat-sink. He used the factory reflector, just cut the tail off and opens it up for the LED. It's direct drive, no regulation or any fancy circuitry and can run off of Alkaline or NIMH D-cells. The LED is a C-bin SSC P7, rated at a max output of around 900 Lumens. I run it on alkalines so I am only getting about 650-700 Lumens out of this thing, but on fresh cells it'll run a good 4 hours or so at max output.

I removed the factory lens and installed a UCL glass lens as well as a KIU stainless VL Bezel with GITD teeth holes. The red 3D Maglite next to this ElektroLumens one has a Terralux SSC P4 LED drop-in with a KIU stainless LP bezel.
I have a few others but they are real simple lego mods, nothing special.
2xTap
-
-
Closest I've come to torch mods is a few simple drop-ins on my maglites (no actual modding required TBH :D). Love your stuff though Essexman.

-
Great mod's so far guy's, keep them coming

-
-
Doesn't have to be fancy

-
Well OK, 2D isn't as short as some mods for single 18650's but they still look cute compared to all the really long ones. Shortest I have is a 3D, and I would love throw a brighter drop in in it and give mine to a friend.... any ideas on that front?
I don't mind changing from D cells either

What bulb/emitter do you have in at present?
Honestly can't remember! It's probably a Terralux, something like 100-150 lm-ish. I will give that one away if I can throw something brighter in there instead.
Loving the mods guys

-
@gunga said:
Hmmm, I've done a lot of mods, but they just look like a stock lights. I've done emitter swaps, driver swaps, and other minor stuff. Built a nice Surefire E1L pocket rocket before, but sold it.So, nothing fancy to show...
Same here. I'll try to post my slightly modded Novatac and Elektrolumens Blasters when I'm unpacked.
-
-
-
-
-
-
I think the Solitaire works better as a pill carrier than it does as a torch

-
-
Here's a cheap one. Got one of those "Techlite Lumen Master" lights from a clearance store for $5 bucks. Used to be sold at Costco, Cree XP-E emitter. Build quality is actually really good - smooth threads, quality anodizing, good O-rings, water and shock resistant.
Was happy with it for a while, then batteries started to die really fast (3xAAAs in a holder). Dug around CPF, found out that the "smart" clicky tailswitch has a massive vampiric drain problem that kills batteries in something like two weeks.So, went and got one of those $2 9 LED Aluminium flashlight jobbies, ripped out the tail switch, replaced it, replaced the coil spring with a folded piece of aluminium, added a body spacer and used an 2400mAh IC-protected Samsung 18650 I swiped from a laptop battery pack from a broken laptop.
The end result is a single mode 160 lumen Cree XP-E 18650 flashlight with very good build quality... for about $8 total (including tax). It's warm to the touch after 5 minutes or so (meaning the thermal protection is good), but doesn't get too hot to hold even after 20 minutes of constant running.

Fun fun.
I managed to scavenge 3 good protected 18650s out of that battery pack, I just need to dig up a charger now and I"m golden.
-
That's a hell of a lot of bang for your bucks

-
A proper "MacGyver" light.

-
Took frankenflashlight out for a spin today - worked great. I'm going to have to shine the lens a bit because it's got a scratch, but clean spill, nice (if slightly undefined) hotspot, didn't get hot in my hand. I guess being outside made the heat dissipation much better as it's below freezing. Might see if I can dig up a few more, maybe one of them with a focusable head and try it again.
-
I know this was an old thread but i think it's appropriate to keep it going.
This is my Surefire E2E with a Malkoff M61 260 lumen P60 style dropin inside a Valiant Concepts VME titanium head.
The tail switch is a Z57 clicky type that replaces the twisty/momentary original switch, with a custom made (by me) titanium tail shroud that i designed to complement the shape of the head.



It's a nice torch and i like the Malkoff dropin but due to the dropins brass construction and the extra weight of titanium over aluminium it's a bit too front heavy.
I also tried out the standard valiant head and their delrin tail shroud and i can't decide which looks better. In the future i would like to get hold of a E1 body for this head and run it with an M31 dropin.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login











