Knife making
-
@Mike, Lord of the Spammers! said:
Now that's got "me" written all over it

Dull, rusty, slightly bent but with potential :P
You're too hard on yourself chap.....
That's our job ;)

@sparky415 said:
:D@Mike, Lord of the Spammers! said:
Now that's got "me" written all over it

Its actually got 'Rover' stamped on it

Were is the oil leak , if it was a true Rover it should be in a pool of oil the dodgy electrics/electrician is already sorted :P :D :D :D
-
Gareth, I'm not sure what you mean Mate ;) (175quid :o )
http://www.survival-school.org/Default.aspx?tabid=246&ProductID=1027Mat,
I think they forgot to oil these bits :D -
@sparky415 said:
Gareth, I'm not sure what you mean Mate ;) (175quid :o )
http://www.survival-school.org/Default.aspx?tabid=246&ProductID=1027Mat,
I think they forgot to oil these bits :DTony ya have not seen a lack of oil till ya lay your eyes on this Aussie(I think) BAK :ahhh :ahhh :ahhh


It is currently in its 3rd WD40 bath & I can now open the blade + can opener without pliers ::) :ahhh :ahhh.
I got it for $5 on oz Ebay, I think I was had royally :D :D.
I keep thinking I should send this too MTO's resident rust expert Tony
:D :D :D -
-
Mat, I don't think even I would have brought that Mate :D
I recognize some of that wiring AHB ::)
-
@sparky415 said:
Mat, I don't think even I would have brought that Mate :DI recognize some of that wiring AHB ::)
Hidden webcam mate.. >:D ;)
-
Oooh that might be my ex on the table :ahhh
-
So who's the hunchback then..?

-
So who's the hunchback then..?

My newest GF?

:D :D :D
-
I do hope she doesn't read this forum or she may be taking an extra special interest in some of Tony's knives :ahhh :D
-

Noooo you misunderstood

I meant my newest GF at the time

Honest
-
It took me quite a while to get the bits together to make a 'forge' and get a round to having a go at heat treating ;)

I managed to heat it up and hammer out the curve (more or less), left it to cool down which should leave the steel soft enough to work on

When I tried to drill it I found that its still too hard and ruined some cobalt drills on the handle :o
I was going to reheat it but as I have run out of charcoal and time (as I wanted to show it off at the meet) and I was going to make some more orange micata for the handle but time and materials again ::)
So I think to myself I will put a 'temporary' handle on just for the meet
I had an old directors chair in my garage that came to an unhappy ending
this is what I did with one of the arm rests :D

I need to see if I can get an edge on it now and fine tune the handle




-
That's a mean looking zombie chopper mate! Like the forge set-up as well.

-
Thanks Gareth
I could do with hanging around a blacksmiths workshop just to watch and learn, there's so much I don't know
:ahhhI can't wait to have a play with it, I will be bringing it to the meet if I don't break it before then :D
-
That looks awesome tony, the lighter cleaned up nice as well mate

-
@sparky415 said:
I picked this up today ;)
Now your in business. Heat it up red hot and quench straight down ( tip first ) in oil and your ready to go.
-
Tony I was at a Canadian hippy fair recently & they had a blacksmith display/presentation. The miniature forge looked a sweet set up so I took some pics & videos.
The wee forge's air pump re minds me of a old air raid warning siren or a shark alert siren used on Aussie beaches in times gone by ::) :D :D. The wee thing sure got HOT :o 8) 8) 8). It looks like quite a speSmurfpillsed air pump
, the old guy in the vid said most Canadian farmers had a similar set up back in the olden days. Maybe you might find one at a rural car boot sale
:D :DTony happy to send you my still photos if you want mate
, I have not uploaded them yet. -
Thanks Mat but the little videos won't play, it says private

-
I've used one of those hand cranked air blowers before, they certainly give you a good work-out. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
