SuperJuice KFS4
-
ahem bob....
Quote from: J-sews on July 18, 2010, 01:42:32 pm
Not a bit Ryan, but thanks for the prodding . I'll get back to working on it this week
Bob
-
LOL! the "Master" we call J-sews does have a rep here!

but my gawd, when he does finish it's a thing of beauty and envy!
one thing I so like about Bob's projects are the fantastic pictures and details he gives us!

Wonderful project uncle Bob!

-
(not ignoring btw, but not done yet either...) :)
-

is that enough pokes? :D
-
I thought it was a diagram of stacked cell membranes.

-
That confirms my headache.. now where'd I put the tylenol

-
-
bob im not letting you off not finishing this yet >:D

-
Not to worry Ryan, I'll not be setting it aside as long as (one of) my previous projects. ;)
Which, by the way, was finally completed a few days ago... :P /topic/1167
-
Bumping because I don't want to see this incredible project go unfinished.

I'm dying to get an XE6 myself and do some modding to it. Is it really that hard to take it apart and reassemble it? I wanted to drop the straight edge and saw to make it as thick as a CS4, replace the flat driver bits with a custom made setup that would allow the use of power driver bits,

and also do something with that ridiculous corkscrew. ::)
Unfortunately I don't have the equipment that J-sews does so readily available. I'll have some access to a welding shop I used to work at, but I can't do whatever I want like I own the place.
In the meantime I'd be happy if J-sews would update us on any progress and/or post more multitool porn.

-
Glad this got bumped, as now I'm rethinking the mod idea. Just don't have the tools to drop in a can opener. Thought the process would of not been so difficult.
Did ask someone at Leatherman about the rivets and/or replacements, no dice.
Don't understand the fascination of a corkscrew. Chako says to use the Vic/SAK screw thing, but the Juice already have a small screwdriver, seems pointless to add yet another screwdriver to justify the corkscrew.
■ Add a thin carabiner
■ Foil Cutter or a long C blade utility knife
That corkscrew doesn't feel natural either, and catches on the sheath.
I ♥ the saw personally. Sharpen the tip similar to the can opener, and square-sharpen for penetration. Worked great for pumpkin carving too!
And I work the Awl to a near knife edge, clean the tip to penetrate material better without warping the metal, and square sharpen everything for better cutting. Then stone down the edges for an even sharper corner edge.
-
-
It's ok Bob, my sideclip polishing project barely left the ground before I put it on the back burner, and all I have to do is polish it then assemble it! You have to make stuff for your mod, I sympathize!
-
@J-sews said:
Then things were proceeding nicely again, until it became apparent that my pivot screws are too short. :'( The ones I bought from www.knifekits.com are one half inch long:
Unfortunately, it appears they need to be just a little bit longer. :( These are already the longest ones knifekits sells, so I'll have to make my own.
Just curiously, what diameter are the pivot pins?
I have a coupla semi-børked Juices, and have been considering a layer mod, and really REALLY didn't wanna have to deal with peening pins!
(Before anybody asks: Knife, Scissors+Bottle Opener, Saw (yes, saw)+Awl, File. No serrated knife, no freakin' corkscrew. Basically, a KF4 with scissors instead of the serrated blade.)
I'm betting they're prolly some 300-series stainless. Too bad you couldn't harden them...
The Juice pins are 5/32 (or .156") in diameter. Unfortunately though, they are just slightly too short to work on a tool of Kf4 thickness. :( You would have to drop one whole layer in order for these pins to work. >:(
What if you just made two of those pivot tubes into one, and fixed them togehter with a grub screw in the middle? Would that become loose too quickly? I can't really see the flaw. Except... I was looking for those pivot screws on knifekits.com, can't find them in the .156 variety. Discontinued or am I just too thick to look properly?
-
Woohooohhooooo maaan!! Some awesom work and idea! Hat down to you sir!!
Can't wait end result!!
-
:pok
thats all i have to say
-
Can't wait to see the result!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
