Getting a multitool: Leatherman or Gerber?
-
Hi guys, I'm back again!
The Wave has served me great over the last 11 months and am rarely seen without it on my side!
However, back again to the legalities of carrying a locking blade. Sure, when I have a need for it, that's great! However, I do literally have my Wave on my side all the time, even when I don't need it (or don't think I will, should I say!). I'm looking to purchase a second multitool purely for going out and about in, so to speak, that is knifeless. The one that springs to mind is the Leatherman Knifeless Fuse, especially as I'm very happy with Leatherman. However, the most common tool I use is the pliers, which need to be unfolded before use. On my Wave I have worked into it a lot so i can flick open the tool one handed to access the pliers, but with this I find that if I grip very tightly on something when I open the pliers the 'legs' will move but the pliers will stay gripped to the object (does that make sense??). So the requirements for this tool are for it to be knifeless and hand one handed access to the pliers. The reason the Knifeless Fuse doesn't do it for me is access to the pliers which I can access one handed like my Wave if I work into it, but then I loose the stability of the pliers.
What I'd like is as mentioned earlier in the thread the Gerber Compact Sport 400 or something similar (with the very easy one handed access to the pliers). Unfortunatly there is a knife. As far as I'm aware, Gerber don't make a knifeless multi tool with the flick opening. If they do I'd more than likely go for this tool. However, if I were to purchase this Gerber or some equivilent, what is the possibility of me removing the knife on it?
Thoughts and opinions please, and suggestions as to a multitool that meets the requirements! As I wish to EDC this multitool, I don't want it to be huge either, no bigger than a Wave which I'm fine to EDC now! :)
Thanks very much in advanced,
HobitEDIT: As I want to EDC I still want as many other features as you can throw at it!! :D
-
A good option might be something from SOG. Easy to flip open and the blade can be swapped out for another tool.
-
Without knowing much about your application , I would have a good look at the Wave . Good solid middleweight contender !
Chris
-
Several people might bash me for saying this, but you could always break the knife blade off if you are sure you will never use it...
-
How about a knife-less Wave :P :D :D :D
Glade your Wave has worked out for you mate 8) 8)
Gerbers are probably easier to pull apart than Leatherman , just need a vise-grip tool & I reckon someone here could supply a Gerber saw or a file to replace the original blade
.Now the slotted Gerber washers , they take a bit of fiddling to get in place :ahhh :ahhh. I have been told with practice it gets easy ::) :D :D :D
-
@joebw said:
Regardless of the make of tool, the owner needs to take care of it. Remember stainless steel means STAIN less! Please think about ending this meaningless diatribe.Thanks - Joe
Truer words were never spoken. People need to take care of their tools.
As for the diatribe, well, I wish it would end too, but I doubt that will ever happen. ::)
Def
-
I'll jump on the SOG bandwagon. Pick the size you need and remove the blade/s. Tool swapping is much easier than on other makes.
Be careful with SOG flicking though, many here have bruised knuckles due to that sport :D
-
Ducktape never rusts. Just sayin. :)
-
Juat to reiterate it again: is there a way of taking the knife off the Gerber Multi Plier Compact Sport 400? Or is there already a multitool similar that is knifeless?
-
The Leatherman Fuse is available in a bladeless version, and SOG tools are the easiest to remove the blade, plus the blade can then be replaced with another tool.
There are two ways to remove the blade from Gerber's MP400. The easiest way is to snap it off. I'd suggest locking the blade into a vise and with a quick jerk snap the blade off where the edge meets the tang. The other, is to try and disassemble it, remove the blade and re-assemble it, but Gerber doesn't make them easy for tampering. You will also need something else to fill in the slot where the blade was removed so that the leftover tools don't rattle around. This may take some scrounging or fabrication work to get right, and probably a fair bit of trial and error. Plus, unless you manage to find a donor Gerber tool, you are going to be one function short, which may or may not be of use to you.
You'd probably be better either with the bladeless Fuse, or to try and take the blade off something like the Octane if you like the sliding plier head.
Def
-
@Grant Lamontagne said:
You'd probably be better either with the bladeless Fuse, or to try and take the blade off something like the Octane if you like the sliding plier head.I would into that. Apparently, it takes just a torx driver, and makes the tool slimmer. The one thing is the Octane doesn't have scissors, which I believe are key to a knifeless multitool.
-
Whatever you get Hobit...get something awesome. You'll be an old man someday and look back .....and say to yourself..."I remember when...this one time I needed this tool for....I've had this since I was 18...my,my,my..."

-
Leatherman rocks :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




