Charge saws
-
Hoping it warms up just a tad more. Studied the thread in a more relaxed mode, and seems maybe keeping the saw blade the way J-Sews did is would be better in that the closed handle supports the saw blade from wobble.
Need to shorten this Sawsall blade anyhow (so it can fit in the sheath for EDC) and have enough Dremel sanding drums to work that shoulder curve.
Wished I could get a set, or a few, from J-Sews. :D
-
@Xelkos said:
Hoping it warms up just a tad more. Studied the thread in a more relaxed mode, and seems maybe keeping the saw blade the way J-Sews did is would be better in that the closed handle supports the saw blade from wobble.Need to shorten this Sawsall blade anyhow (so it can fit in the sheath for EDC) and have enough Dremel sanding drums to work that shoulder curve.
Wished I could get a set, or a few, from J-Sews. :D
The guy can be a real scrooge, but I'll talk to him and see what he says. ;)
-
J-sews may seem like a scrouge but on the inside he is a softy.:)
-
I'll have a charge coming this week and I can't wait. J, any chance of any more saws being produced? It seems like a tremendous addition to the tool.
-
The fiberglass wheel took a beating this morning and dern if I didn't muck it up. Now have a 3 incher sawsall, and it fit great - till I cleaned up the sharp edges. Slight amount of play, nothing major. Perhaps seeing someone else's work will give me a clue.
The very first one I did was the best, yet it was 2 inches too long. Should of just cut the other end off. :'(
Think the problem I'm having (besides adequate lighting) is the shoulder where the blade slides under the ruler edge, that L can't get square enough and that's the wobble.
Should of done like I did last week, left this tab longer - keeping it squared & uniform. -
@AncientMatingCalls said:
I'll have a charge coming this week and I can't wait. J, any chance of any more saws being produced? It seems like a tremendous addition to the tool.Yup, I'll be making more soon :)
-
I'll have a charge coming this week and I can't wait. J, any chance of any more saws being produced? It seems like a tremendous addition to the tool.
Yup, I'll be making more soon :)
!! YIPEE !!
/grovels before the Master
-
Now I'm even more excited to get my Charge.
You sir, are a very generous man J.
-
BOB! WOW!! Just got your saw in today and it fits like a glove. I bow to your skill superiority!


-
@SlackOne said:
I made the one in my avatar a few days ago. $2 saw blade + dremel + cutting wheel + chainsaw sharpener = cheap and cheerful fun. Works pretty well, too. The solid side panels on the Charge might be sturdier in the long run than my Wave, though.How did you use the Chainsaw Sharpener to cut yours, SlackOne?
-
@Xelkos said:
BOB! WOW!! Just got your saw in today and it fits like a glove. I bow to your skill superiority!
Glad it arrived safely James! :)
Now go try it out on something!
:D -
Can't believe I didn't find this thread ealier... going to have to dig out the dremel.
-
J-sews, how can I get one of these saws, to give it a try on a Wave?
-
-
I'll pationlly wait.

-
@Xelkos said:
I made the one in my avatar a few days ago. $2 saw blade + dremel + cutting wheel + chainsaw sharpener = cheap and cheerful fun. Works pretty well, too. The solid side panels on the Charge might be sturdier in the long run than my Wave, though.
How did you use the Chainsaw Sharpener to cut yours, SlackOne?
The chainsaw sharpener was one of the Dremel grinding bits I had on hand...long and thin to get into the teeth of chainsaw blades. It just happened to also be an elegant shape to do clean up on the cuts I did with the cutting wheel.
-
Getting a Surge in the new year would be happy to test it out for you :)
am always dithering about with knives cutting away unwanted things. -
Bad news:
The saw blade idea will NOT work in my Surge. :( It has a little cast rounded D-shape component at the end of the handle, which is only held in place with the one screw. During sawing motion, the Sawzall blade overpowers this one screw and flops around uncontrollably.I beg to differ. I am working on a solution for the moving clip for the Surge and I will send you the particulars soon. I believe it can be done. If I am wrong I will admit in this forum.
-
J-Sews
The blade works GREAT! Used it to cut a few knobs of metal, and even some wood. Marred up the paint so stripped it off, polished it up, and now EDCing it in the leather Charge sheath. Soon as I get over this bug am going to get some carbon sawsall and keyhole blades to hopefully whittle out to fit.
Soon as I got time to do something I got held hostage by an alien virus. Knew I should of gotten that flu shot this year... :'(
-
@Xelkos said:
I made the one in my avatar a few days ago. $2 saw blade + dremel + cutting wheel + chainsaw sharpener = cheap and cheerful fun. Works pretty well, too. The solid side panels on the Charge might be sturdier in the long run than my Wave, though.
How did you use the Chainsaw Sharpener to cut yours, SlackOne?
The chainsaw sharpener was one of the Dremel grinding bits I had on hand...long and thin to get into the teeth of chainsaw blades. It just happened to also be an elegant shape to do clean up on the cuts I did with the cutting wheel.
Seen a tungsten carbide one for $14, almost got it. Need to get some more fiberglass cut-off wheels too.
<3 your blue blade. Wonder if I can find one in red? >:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login