Skeletool production differences .
-
@Kender said:
It's funny that you bring this up. I had noticed the same thing on a different model: my Japanese-made PST opens with the handles much farther apart than my USA ones. I thought it was a fluke, but maybe it is a production difference...Yes I can remember my Japan PST have a few differences .
I got my CX combi blade from Amazon UK last January.
Mine's the same as your CX i.e. opens to 7cm :)
So they didn't change it with the blade then .
When you have one in either hand you can really feel the difference .
Sawman just to confirm are all yours 6cm or 7cm if you don't mind measuring them ;)
They are 7cm.

-
Great spot Dunc!
You sure do have an eye for the details! 8)Mine are about 10mm different, same as yours. I've no idea why either.

-
Also, did you notice the first hole in the knife, the one the detent engages, is bigger on the newer models?

-
@J-sews said:
Also, did you notice the first hole in the knife, the one the detent engages, is bigger on the newer models?
No I didn't ( now checking :D ). Oh yes , I wonder why that is
Also I noticed the small cut out at the base of the blades edge ( not very noticable in my last photo ) but its not on the stock photos on LMs site but is on the current production models . -
Looks like we've got to the bottom of this I emailed Leatherman and they replied asking if they could use my question and answer it on their facebook page
http://www.facebook.com/topic.php?topic=352&post=2009&uid=122239001148610#post2009Recently one of our fans here noticed a discrepancy between the widths of handle sets on two Skeletools he had. He opened them up and put them base to base and one has a width of about and inch (from the inside of the carabiner to the inside of the bit in the driver) and the other about and inch and a half. These are rough measurements. Anyhow…He asked us what this was about and why we would have done this.
I went down to engineering and they said:“The old standard Skeletool had no/or little clearance between the handles right below the jaw. This creates problem of pinching your palm when people are squeezing the handle because the handle are bottoming out. The new revision has more clearance between the handle near the jaw so that pinching when squeezing handle is no longer an issue.”
Since Skeletools don’t have the date stamp on them like other tools, I can only tell you that we did this change in late 2008. Because we have no way of knowing what stock is still out where, its’ possible (though not likely) that you could find one of these old ones.
An update to those who have commented about the jaws breaking…We have narrowed this down to just when they are being twisted. We have made adjustments and added material to the jaws themselves (minute, yet effective in testing, amount of material). This change will be making its way on the manufacturing floor very soon. It’s been in testing phase, but is complete now. Of course if you have any problems before then, the warranty is always good and anything that happens just send it into us and we’ll take care of it and send you a new one.
So looks like we are all going to have to look out for the new beefed up plier version , more money lol
-
Nice new information from Leatherman. By the way, when did they change that spacer which stops liner lock to a bigger one - did they sell any of those with smaller ones or was it only prototype for promo shootings?
-
@mtool78 said:
Nice new information from Leatherman. By the way, when did they change that spacer which stops liner lock to a bigger one - did they sell any of those with smaller ones or was it only prototype for promo shootings?As far as I know non of the small spacers made it into production . I could be wrong but I've never seen one on here .
-
I knew about the handle differences when I got my two newer Skeletools and lined them all up for a photograph. The difference is fairly noticeable once you line them all up for a mug shot. Nice to have Leatherman confirm it though.

-
Hey Dunc, I want to take and ask, what the material is the tip of the pliers of the Skeletool is made?
Because I think it's a bit weak. The my Skeletool CX is broke,I sent it to warranty and already received.
But now I was scared of breaking again.Thanks!!
-
@Macário70x7 said:
Hey Dunc, I want to take and ask, what the material is the tip of the pliers of the Skeletool is made?
Because I think it's a bit weak.Thanks!!!
I don't know exactly , some kind of cast steel .
@Chako said:
I knew about the handle differences when I got my two newer Skeletools and lined them all up for a photograph. The difference is fairly noticeable once you line them all up for a mug shot. Nice to have Leatherman confirm it though.
I must of missed your thread about it .
Dunc
-
@Dunc said:
Looks like we've got to the bottom of this I emailed Leatherman and they replied asking if they could use my question and answer it on their facebook page
http://www.facebook.com/topic.php?topic=352&post=2009&uid=122239001148610#post2009Recently one of our fans here noticed a discrepancy between the widths of handle sets on two Skeletools he had. He opened them up and put them base to base and one has a width of about and inch (from the inside of the carabiner to the inside of the bit in the driver) and the other about and inch and a half. These are rough measurements. Anyhow…He asked us what this was about and why we would have done this.
I went down to engineering and they said:
“The old standard Skeletool had no/or little clearance between the handles right below the jaw. This creates problem of pinching your palm when people are squeezing the handle because the handle are bottoming out. The new revision has more clearance between the handle near the jaw so that pinching when squeezing handle is no longer an issue.”
Since Skeletools don’t have the date stamp on them like other tools, I can only tell you that we did this change in late 2008. Because we have no way of knowing what stock is still out where, its’ possible (though not likely) that you could find one of these old ones.
An update to those who have commented about the jaws breaking…We have narrowed this down to just when they are being twisted. We have made adjustments and added material to the jaws themselves (minute, yet effective in testing, amount of material). This change will be making its way on the manufacturing floor very soon. It’s been in testing phase, but is complete now. Of course if you have any problems before then, the warranty is always good and anything that happens just send it into us and we’ll take care of it and send you a new one.
So looks like we are all going to have to look out for the new beefed up plier version , more money lol
Dunc,
That's awesome! It's great that Leatherman is willing to tell all about a tool.

Just another reason it's such a quality company.
-
Thanks for pursuing this Dunc!
Its always nice to get the whys? answered right from the source.
It's also good to know that the Leatherman engineers are willing to make incremental improvements when needed, not just kick back and relax after a tool hits production. :)So I'm guessing the bigger notch in the washer and the bigger hole for the liner lock detent were both added in 2008 when they did the anti-pinch change to the handles. :)
-
The notch in the blade you're talking about actually helps with sharpening. It's a notch between the ricasso and edge of the blade. On a blade that the sharpened edge goes all the way to the ricasso (unsharpened portion near tang), it is difficult to get the last little bit sharpened, this help in that. I sometimes cut one into knives that don't have one with a triangular file.
-
@SuzukiGS750EZ said:
The notch in the blade you're talking about actually helps with sharpening. It's a notch between the ricasso and edge of the blade. On a blade that the sharpened edge goes all the way to the ricasso (unsharpened portion near tang), it is difficult to get the last little bit sharpened, this help in that. I sometimes cut one into knives that don't have one with a triangular file.Thanks for the info

-
@SuzukiGS750EZ said:
The notch in the blade you're talking about actually helps with sharpening. It's a notch between the ricasso and edge of the blade. On a blade that the sharpened edge goes all the way to the ricasso (unsharpened portion near tang), it is difficult to get the last little bit sharpened, this help in that. I sometimes cut one into knives that don't have one with a triangular file.Another thought on this
I was cutting a sheet of bubble wrap with the blade and I found that the cutout can snag what your cutting and hook up :( I wasn't too impressed as it was only a simple case of cutting a strip off said bubble wrap , I'll see how it goes . -
This is some thing I`ve noticed for some time and not just with the Skeletool. My Skeletool CX new ver. is much wider than my older Skeletool. Like Dunc shows in his opening post. I find it the wider handles are really to wide.
I took my Skeletool CX apart to file it down to get a better fit for my hand. Then I couldn't find my small file and have not found one at the hardware store yet so I put it back together and live with the to wide handles. -
Dunc Thanks for posting pics. I havelooking to buy and have been handling several skeletools, and had almost ruled them out due to the ones that opened wider.(it hurts my hand to try and hold it I guess I have small hands) I even asked about it on the Facebook page where I noticed it between a skeletool, and a freestyle and of course no one but me seemed to know what I was talking about. But I didn't think to get a pic at walmart.
I will say this as well. The store I was looking at had 3 skeletools on clearance. I had wen't and looked a couple of times because once I was wearing a wrist brace, and it partially covered the palm of my hand originally causing me to think that was why the handles felt so wide. But I went back and handled another one ,so they actually turned out to have both sizes in the batch of 3 they had left. These were all PE skeletools.David did it look like it could be filed down and still work properly? other than the "pinching" issue?
I want one but the wider ones are just too wide. I will either have to file/grind one or find one of the narrower gripps, and then there is the warranty issue.
-
@chris777 said:
Dunc Thanks for posting pics. I havelooking to buy and have been handling several skeletools, and had almost ruled them out due to the ones that opened wider.(it hurts my hand to try and hold it I guess I have small hands) I even asked about it on the Facebook page where I noticed it between a skeletool, and a freestyle and of course no one but me seemed to know what I was talking about. But I didn't think to get a pic at walmart.
I will say this as well. The store I was looking at had 3 skeletools on clearance. I had wen't and looked a couple of times because once I was wearing a wrist brace, and it partially covered the palm of my hand originally causing me to think that was why the handles felt so wide. But I went back and handled another one ,so they actually turned out to have both sizes in the batch of 3 they had left. These were all PE skeletools.David did it look like it could be filed down and still work properly? other than the "pinching" issue?
I want one but the wider ones are just too wide. I will either have to file/grind one or find one of the narrower gripps, and then there is the warranty issue.
Chris, while I haven't done a Skeletool yet. There are two main areas You can file. The springs, plier head or both. Just remember not to change angles and dont file to much off. Check often for fit. At this point I`ll probably just live with it as is. The Skeletool can be a challenge to get back together. :)
-
If you do take a file to it remember you will void your warranty .
-
I have to get one first.
I got a new version of the wave under warranty and have been trying to get used to the wider opening compared to my original version.
Meanwhile I have been hoping to score a skeletool on clearance or used.
I almost got an old PE with im assuming the narrower opening handles at wallyworld, on clearance for $45, but I really want the cx PE, which will either have to live with or file down, (plus i was hoping they would cut the price again, but they ended up selling first.
Mayby I can get a pair on the boad.
Ive been carrying the wave since I can now add the pocket clip. and its nice but I still want a skele to see if it would do the job.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login