Blade steels
-
Here's a link for anyone with an interest in knife steel :) ...
http://www.cutleryscience.com/reviews/blade_materials.html#S_VG10
-
I have the D4 (non waved) in VG-10 and really like it. I don't put my knives through a rough life, so I can't really say much from a hard-use standpoint, but from everything I read, VG-10 sounds like about the best comprimise out there, and seems to be about the "best" steel that almost everyone likes and agrees is still practical. It hold a good edge and is very stain resistant (I think Spyderco uses it in some kitchen knives). S30V and ZDP189 are the two big ones that some (but not all) would claim as "better", but they get tough to sharpen and can be brittle and also stain more quickly IIRC. All that to say if I had my pick of any steel I'd usually go with VG-10, with ATS34/154CM as my next choice.
I've certainly not got anything against softer steels (420 etc), in fact I like them and the ease in resharpening makes up for a lot of the loss in edge-holding IMO, especially if its a well done blade. -
@NeitherExtreme said:
I've certainly not got anything against softer steels (420 etc), in fact I like them and the ease in resharpening makes up for a lot of the loss in edge-holding IMO, especially if its a well done blade.Exactly mate, softer steels are fine as long as there heat treated properly :)
-
I'm not a steel snob but heres what little I know . I think its right but not 100% . Aus-8 is a good alround steel thats similar but slightly better then 440A and B . 154cm is the American Version of Japanese ATS-34 and both are regarded as one of the best knife steels , you do need to know what your doing whith sharpening though .VG10 is a very good steel that I have enjoyed using and found it sharpened quite easily . Just about all VG10 is made in Japan . S30V is a very high end steel with superb edge retention . It is prone to micro chipping on the edge but I have never experienced it . A real b*gger to sharpen but worth spending the extra time on the stone, Chris Reeves uses it alot .
Dunc
-
I like all of the "wondersteels." 420 and 440 just dont last as long in my opinion. 154cm and ats34 are both great steels. I have a lot of experience with them and I can say that they are hard to sharpen but well worth the effort.
-
I don't know a whole lot about different steels but I do have a Spyderco Navigator 2 that has VG-10 steel and it has stayed sharp MUCH longer than any of my other knives, most of which I'm assuming are 420 or 440 stuff.
-
@ducktapehero said:
I don't know a whole lot about different steels but I do have a Spyderco Navigator 2 that has VG-10 steel and it has stayed sharp MUCH longer than any of my other knives, most of which I'm assuming are 420 or 440 stuff.There is alot to be said of VG-10 and something I'd like to know more about in 2008
Dunc
-
Getting a Falkie F1 would be a good way to find out :)
-
Or a Tomcat!
Actually, SOG is converting many of their knives from AUS-8 to VG-10 (at no extra cost).
I love VG-10, but AUS-8 is acceptable.
-
@micky d said:
@micky d said:
Getting a Falkie F1 would be a good way to find out :)
I've been thinking about getting an F1 lately, but I've heard the new models are coming out this year, so I may wait.
Where did you hear that ???, have you got a link mate :)
I think that Peter mentioned that in the Fällkniven forum at knife forums, but he didn't mention any detail about what will be tha changes (new steels, maybe 3G in the F1), or what new models will be for this year.
Carlos
-
@micky d said:
@micky d said:
Getting a Falkie F1 would be a good way to find out :)
I've been thinking about getting an F1 lately, but I've heard the new models are coming out this year, so I may wait.
Where did you hear that ???, have you got a link mate :)
I think that Peter mentioned that in the Fällkniven forum at knife forums, but he didn't mention any detail about what will be tha changes (new steels, maybe 3G in the F1), or what new models will be for this year.
Carlos
Hmm, i'm not sure I like the idea of 3G, I mean it's bound to drive the price up :-\
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login