Sharpening stones
-
Hmmm... I just looked at the hunter's honer. It's 2000 grit ceramic. Should be similiar to the 2200 grit ceramic I got from DMT sharp. That is around 7 microns. It should give you a very polished razor edge. To compare 600 grit which is usual for most utility sharpeners, DMT has one at 750 grit is around 25 microns. I presume you are refering to the Eze-Lap block sharpener. That is probably more a utility grit in the 600 to 750 range. I'd get both. You might want a grit in the 1000 to 1200 range for intermediate sharpening. Ceramic stones are real easy to clean the glazing on if it builds up. Just lightly scrub with a little Comet. The only thing I might consider is that the hunter's honer is about $30. The DMT Diafold I got was $40. It gives you both a 1200 grit diamond on one side and a 2200 ceramic on the other. Check it out at www.dmtsharp.com.
At the point of a polished edge it's going to be more a matter of how fine an edge a typical multi-tool blade will hold. My new stones come tomorrow and I will find out.
I also have a Smith's sharpening jig. It sets at a 20 or 25 degree angle and has a 325 grit for shaping the bevel and a 750 grit for fine sharpening. Also included is a triangle Arkansas stone for serrated edges. It works real good but the clamp can scratch the knife a bit. It costs about $25.
-
The Diafold's are a really good bit of kit, I've used mine for what must be at least ten years and it's held up really well :)
-
"kit" boy you Brits.
If you really want to get anal I was looking on Amazon and they carry the Shapton brand of ceramic waterstones. They go all the way to 12000 grit. From the reviewers comments it will produce an edge far sharper than a razor. One of those will set you back for just under $100.
-
@FredKJ said:
"kit" boy you Brits.If you really want to get anal I was looking on Amazon and they carry the Shapton brand of ceramic waterstones. They go all the way to 12000 grit. From the reviewers comments it will produce an edge far sharper than a razor. One of those will set you back for just under $100.
I think 12k really is for the anally retentive amoungst us :D
-
Yeah but now that I see it I want. I guess it's that Benner magpie syndrome. I do have some carving knives. 2200 grit is probably at the upper limit of an edge that you can put on the steel of a typical multi. It also gives a decent polish. It's really hard to put an edge on that refined and it takes a very good steel to hold an edge like that. You also have to be very skilled to produce an edge at that level.
-
A mate of mine (unka colin for those who know)uses up to that grade when he restores swords and knives :)
But year your right, it takes a fearsome amount of skill to use a stone like that properly :o
-
Yeah but now that I see it I want. I guess it's that Benner magpie syndrome.
I've been really good recently. :)
Is that along the lines of what Mae West would say, "When I'm good I'm good, when I'm bad I'm better"?
I was looking at a reviewer telling how to test an edge on that stone. Run it on the back of your head and if it catches on the hair and stops it's ready. Of course it seems like you could cut your neck in the process. An edge like that will cut by just being near something. I might get the DMT 8000 grit diamond though. It might cut a little more aggressively and should still give a good polished edge.
-
@micky d said:
Yeah but now that I see it I want. I guess it's that Benner magpie syndrome.
I've been really good recently. :)
You must be so proud, having a diesease nammed after you :D
So are you trying to say I have contracted BMS when it comes to sharpening stones or something? Is this like an intervention?
-
@micky d said:
Yeah but now that I see it I want. I guess it's that Benner magpie syndrome.
I've been really good recently. :)
You must be so proud, having a diesease nammed after you :D
So are you trying to say I have contracted BMS when it comes to sharpening stones or something? Is this like an intervention?
Once you get over the 100 posts mark your done for basically :D
-
I think I'll know when I pass the point and bottom out. It's not that I cannot afford sharpening stones. It's knowing I am getting past the limit of using my 60x-100x handheld microscope to examine edges and have to go out an get an electron microscope. But then I know that a refined razor edge actually grows and changes over time by just sitting there due to chemical and mechanical processes. And that I know that is probably pretty sick. Perhaps I can spend a month at a rehab center with Britney Spears. Maybe she'll let me shave her head. :D
-
I got my new stones the other day. I found out DMT now makes a sharpening jig that holds the Diafold stone. I don't have one but figured out how I can use it in my Smith's sharpening jig to get a nice bevel. Since I am doing whittling with my son I need it really sharp. Instead of a high end stone I have ordered a FlexCut slipstrop with some stropping compound. I should have it in a few days. The Vic blade has a Rc 56 which isn't has hard as my carving tools, Rc 61 but should hold a sharp edge decently for whittling.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login